Sharp FO-3800M, Руководство по обслуживанию

Страница: 91 / 180

26
-
30
Purpose Setting
Function
(Purpose) Used to set the CE mark conforming operation mode.
(For prevention against flicker when driving the fusing
heater lamp)
Section Fixing (Fusing)
Item Specifications Operation mode (Common)
Operation/
Procedure 1) The currently set code of the CD mark conformity
(Flicker prevention) is displayed.
2) To change the set content, enter the code of your desired setting
and press the start button. The set content is stored.
Set code CE mark conformity operation (Flicker prevention)
0 YES
1 NO
When the power of this machine is turned on, if any lamp flickers
during printing, set this setting to "1" (YES). Then the phenomenon
may be prevented or reduced.
26
-
38
Purpose Setting
Function
(Purpose) Used to set the photoconductor drum operation inhibit
YES/NO when the life is reached.
Item Specifications Operation mode (Common)
Operation/
Procedure 1) The currently set code of the machine operation
at photoconductor drum life is displayed.
2) To change the set content, enter the code of your desired setting
and press the start button.
Set code Machine operation at photoconductor life
0 Operation stop
1 Operation allowed
When this is set to "1," the copy/print operation can be performed
even if the photoconductor drum reaches its life (20K). At that time,
the copy/print operation can be performed regardless of the
photoconductor drum counter value.
When set to "0," if the photoconductor drum counter reaches the life
(20K), the copy/print operation cannot be performed.
If the photoconductor drum counter reaches the life (20K) during
continuous copy/print operation, the machine completes its job before
disabling the operation.
26
-
40
Purpose Setting
Function
(Purpose) Used to set the scanner (writing) motor OFF timing.
Section Laser (Exposure)
Item Specifications Operation mode (Common)
Operation/
Procedure 1) The currently set code of the scanner (writing)
motor OFF timing after completion of printing is
displayed.
2) To change the set content, enter the code of your desired setting
and press the start button.
Setting code Scanner (writing) motor OFF timing
0 0 sec
1 30 sec
2 60 sec
3 90 sec
26
-
44
Purpose Adjustment
Function
(Purpose) Used to adjust the rear edge void area in the SPF
copy mode. (AL/FO Series only)
Section ADF/RADF/UDH/SPF
Item Operation Copier
Operation/
Procedure 1) Enter the adjustment value and press the START
button.
(The adjustment value is stored.)
2) Check the copy rear edge void area in the normal copy mode.
The greater the adjustment value is, the greater the rear edge void
are is.
The adjustment value input range is 0
∼
8, and the default is 4.
When the adjustment value is changed by 1, the image loss varies by
about 1mm.
26
-
47
Purpose Adjustment
Function
(Purpose) Used to adjust the rear edge void area adjustment in
the FAX mode.
Section ADF/RADF/UDH/SPF
Item Operation FAX
Operation/
Procedure 1) Enter the adjustment value and press the START
button.
(The adjustment value is stored.)
2) Check the copy rear edge image loss in the FAX mode.
(Make a copy in the FAX print adjustment mode of SIM 46-12 and
check the void area.)
The greater the adjustment value is, the greater the rear edge void
area is.
The adjustment value input range is 0
∼
8, and the default is 4.
When the adjustment value is changed by 1, the image loss varies by
about 1mm.
30
30
-
1
Purpose Operation test/check
Function
(Purpose) Used to check the operation of the sensors and
detectors in the paper feed section, the paper
transport section, and the paper exit section and their
control circuit.
Item Operation
Operation/
Procedure The paper detectors operations can be checked with
lighting of the lamps on the operation panel.
Detector name Monitor lamp
Paper empty
detector PE SENSOR Developer cartridge
replacement lamp
Paper entry
detector PIN SENSOR Paper jam lamp
Paper exit
detector POUT Photoconductor
cartridge replacement
lamp
Paper size
(width) detector PAPER SIZE
SW Zoom lamp
FO-3800M
8 – 9