注意！
使用隨附吸頭時（毛刷吸頭、狹縫吸頭）
操作方法
使用附屬吸頭時（除塵毛刷吸頭、狹縫吸頭）
除塵毛刷吸頭
狹縫吸頭
適用於清掃家具上方等高處。
請確實插入後再使用。
可安裝於主機或延長管上使用。
使用
以主機朝上的方式清掃時，運作期間
請勿按下 。
要停止運作時，請先將吸頭朝向下方
後，再按下 。
在朝向上方的狀態按下 時，垃圾
可能會由主機上掉落。
咔嚓
安裝
咔嚓
安裝
裝卸按鍵
拆下
裝卸按鍵
拆下
咔嚓
安裝
裝卸按鍵
拆下
咔嚓
安裝
裝卸按鍵
拆下
卡榫
要改變角度時，請按住卡榫並同時轉動。
注意！
改變角度時，請注意避免手掌
或手指被旋轉部位夾傷。
前端部位
旋轉部位
注意！
請避免手掌或手指被夾傷。
請同時按住主機或延長管上的裝卸
按鍵拆下。
請確實插入後再使用。
使用
避免馬達因密閉而過熱的
開孔。
請勿將其堵住。
適用於清掃家具之間的縫隙及窗框等處。
可安裝於主機或延長管上使用。
※請勿用於清掃鋼琴等
容易刮傷的物品。
同時按住主機或延長管上的裝卸按鍵拆下。
CN-11
CN-12
中文
EN-9
CAUTION
EN-14
EN-13, 14
EN-7
EN-17
1
Click!
②
①
3
2
CAUTION
VACUUMING
Flow of cleaning process
Emptying the Dust Cup
Remove the Dust Cup and dispose of
the dirt.
Remove dirt on the Mesh filters
with a cleaning brush.
Press the Dust disposal
hook (yellow) on the side of
the Cover section.
Lift the Cover
section.
Ensure that no dirt
remains at the bottom
of the Dust Cup.
Cover
section
Mesh filter
Mount the Dust Cup.
Protrusion
Dust
disposal
hook
(yellow)
Align the protrusion on the Dust Cup and the
Dust disposal hook (yellow) and insert.
When used continuously for long time
Dust disposal
hook (yellow)
Securely push in the direction of
the arrow
Hook
(blue)
Click!
Recessed
section
Put the recessed section on the Dust
Cup to the hook (blue) on the vacuum
cleaner body
Install the Dust cup assembly
on the vacuum cleaner body.
When the dirt is
entangled and does
not come off
Clean the Dust cup
assembly.
Dust accumulates on the built
in Pleat Filter.
Clean this dust out.
Mounting the Dust
Cup Assembly
Control
switch
The mode toggles between the "High mode" and the "Standard
mode" each time it is pressed.
High mode: When cleaning with maximum suction power.
Standard mode: When cleaning with subdued suction power.
(When a mat or a rug tends to block the Suction head,
for instance.)
Start
Finish
The Rotary brush stops automatically for safety
purpose when the Suction head (roller switch on the
bottom side ) is off the floor while cleaning.
The operation does not stop in such instances.
The rotation restarts when the Suction head contacts
the floor and moved.
Cleaning
completed
Notices
Safety Stop
Even when a cleaning session is completed in the Standard mode, the operation starts with the
High mode if the is pressed the next time.
The Rotary brush of the Suction head automatically turns when the cleaning starts.
When the remaining charge in the battery becomes depleted while operating, the operation is
automatically stopped to prevent excessive discharge that can deteriorate battery. Always charge
the battery each time the product is used for cleaning, regardless of how long it was used.
During the cleaning of mats or rugs, the Suction head may get stuck to the material and the
Rotary brush may stop.
In this case, continue cleaning in Standard mode.
Charging the
battery
Disposing of dirt is recommended
after each cleaning session, for the
purpose of hygiene.
Even when the Suction
head contacts the floor if
the Roller Switch is off the
floor the operation is
temporarily suspended.
Do not touch the Rotary Brush or Roller Switch while the operation is
temporarily suspended.
[Risk of injury when the Rotary brush starts to operate]
Be sure to press the to stop the operation when cleaning the Suction
head.
Caution is required to
ensure that the Mesh
filters (Upper and
Lower) are not lost
while throwing out dirt
or cleaning.
The Dust cup assembly cannot be
installed properly on the vacuum
cleaner body unless it is
completely assembled.
The Pleat filter cannot be installed
on the vacuum cleaner body unless
it is installed on the Dust Cup.
The suction power may decline,
abnormal noise may be heard, dirt
may enter into the motor and other
issues may arise that may lead to
product malfunction unless the Dust
cup assembly is securely installed
on the vacuum cleaner body.
EN-15, 16
EN-15, 16
ENGLISH
EC-A1RHK_A4(W page imposition).indd 29-30
2018/12/06 14:27:02
