sharkclean.eu
sharkclean.eu
SETUP
LIVING WITH YOUR ROBOT
• Place robot on base to charge for
6 hours
.
• When the robot is properly aligned with its
BACK
against the base, the
Charging Icon
on the top
right side of the base will illuminate and the
Battery icon
on the robot will illuminate.
• Make sure the robot is properly aligned on the
base
.
•
TO TURN ON ROBOT:
Place robot on base or press
and hold the
CLEAN
button for 5 to 7 seconds
until the indicator lights turn on.
• Remove protective film from robot and base.
•
Attach the side brushes to the posts on the bottom
of the robot.
• Before cleaning, clear cords and remove small
obstacles like clothing or toys that are less than
8cm tall.
•
Open interior doors
in rooms you want your robot
to clean.
• Find a
permanent
location for the base in a central
area with a
strong Wi-Fi signal
.
• Remove any objects that are closer than 1m. from either
side of the base, or closer than 1.5m. from the front.
• Plug in the base.
The Base Power Indicator Icon
on the top right side of the base will illuminate when
the basehas power. Make sure the power switch on
the back of the base is in the (I) ON position.
ENGLISH
PREP THE ROBOT
STEP 1
..........Side Brushes..........
SET UP THE SELF-EMPTY BASE
STEP 2
Place base
on bare
floor against
the wall.
1.5m
1m
1m
PREP YOUR HOME
STEP 4
Your robot can easily climb over most thresholds, but
if any are higher than 2cm, set up a no-go zone in the
app to block them off.
DOORWAYS AND THRESHOLDS
The base is designed to hold weeks of debris. During
initial use, you may have to empty it more frequently
while the robot finds more debris than usual. Check the
fill level regularly to know when to empty.
CHECK BASE FILL LEVEL
!
AVOID MOVING THE ROBOT OR BASE
While your robot is cleaning,
DO NOT
pick it up and
move it, or move the charging base—this will impact
the robot’s ability to map your home.
Questions? Easy Steps If You’re Stuck:
Having trouble connecting to your robot?
For how-to videos, FAQs, troubleshooting, and tips & tricks visit:
sharkclean.eu.
For full instruction booklet visit:
sharkclean.eu/RV2500SEU-IB.
BASE INDICATOR LIGHTS
Charging Icon
Robot is properly aligned on base and
charging.
Base Power Indicator Icon
Base is plugged in and has power.
Evacuation Icon
Robot is emptying debris into base.
Dust Bin
Release Button
NOTE:
To order replacement parts and filters, visit:
sharkclean.eu
WARNINGS
To minimise the risk of the robot traveling beyond an unsafe boundary
(stair/cliffs edges, fireplaces, water hazards), establish these areas as “no-go
zones” using the mapping feature in the SharkClean mobile app. Upon setting
the boundary, run the vacuum and visually confirm that the settings effectively
prevent the robot from passing beyond the set boundary.
Adjust settings as necessary.
DO NOT
put hands into any opening in the dock or robot.
ERROR CODE
ERROR
#
SOLUTION
(RED) +
(RED)
alternating or
(WHITE) +
(RED)
flashing
2
Blockage surrounding the
brushroll. Remove any debris from
around and inside the brushroll so
that it can spin freely.
(RED) +
(RED)
flashing
2
Side brush is stuck. Remove
any debris from around the side
brushes so they move freely.
(RED) +
(RED) +
(RED)
flashing
2
A drive wheel is stuck. Clean the
wheels and remove any debris
wrapped around the axles so
they can move freely.
(RED)
flashing
6
Front bumper may be jammed.
Clean the bumper and make sure
it moves in and out freely.
(RED) +
(WHITE)
flashing
7
Cliff sensor error. Move your
robot to a new location and
clean its cliff sensors.
(RED)
flashing
10
Robot may be stuck on an
obstacle. Move robot to a new
location on a level surface.
ERROR CODE
ERROR
#
SOLUTION
(RED)
flashing
24
Battery is critically low and needs
recharging. Please pick up your
robot and place it on the base.
Make sure the charging indicator
on the top right side of the base is
illuminated to confirm your robot
is placed on the base correctly.
(RED) FL
(RED)
solid
26
Blockage in dust bin. Check base
and robot dust bin for clogs. Clear
any debris and reinstall the dust
bin, ensuring that it clicks into
place.
TROUBLESHOOTING
IMPORTANT -
Clean filter every month or loss of
suction may occur.
Rinse and let air dry completely. Also, tap loose dirt
off filter between washes as needed.
Foam filters may appear dirty after use–this is normal.
Foam filter
Felt filter
DO NOT
put your hands into any
opening not defined for user access
CLEANING ROBOT'S FILTER
CHARGING YOUR ROBOT
STEP 3
INDICATOR
!
First
Charge
6
h
For full instruction booklet visit:
sharkclean.eu/RV2500SEU-IB.
