SEW MOVITRAC LTP series, Руководство по эксплуатации

Страница: 44 / 80

44
Operating Instructions – MOVITRAC® LTP
8
Selection of Parameter P2-01, Digital Input Function
Parameters
10 O: Stop (Disable)
C: Run Forward O: Stop (Disable)
C: Run Reverse External trip input:
O: Trip
C: OK Bipolar analog
input Connect an external
PTC motor thermistor
or similar to DI3
11 O: Stop (Disable)
C: Run (Enable) O: Analog input
C: Preset speed 1 External trip input:
O: Trip
C: OK Bipolar analog
input Connect an external
PTC motor thermistor
or similar to DI3
12 O: Stop (Disable)
C: Run (Enable) O: Preset speed 1
C: Analog input External trip input:
O: Trip
C: OK Bipolar analog
input Connect an external
PTC motor thermistor
or similar to DI3
13 Normally Open (NO)
Momentarily close to run
forward Normally Closed
(NC)
Momentarily open to
run O: Analog input
C: Preset speed 1 Bipolar analog
input –
14 Normally Open (NO)
Momentarily close to run
forward Normally Closed
(NC)
Momentarily open to
stop Normally Open (NO)
Momentarily close to
run reverse Bipolar analog
input –
15 O: Stop (Disable)
C: Run (Enable) O: Forward
C: Reverse O: Decel ramp 1
C: Decel ramp 2 Bipolar analog
input –
16 O: Stop (Disable)
C: Run (Enable) O: Forward
C: Reverse O: Decel ramp 1
C: Decel ramp 2 O: Preset speed 1
C: Preset speed 2 –
17 Normally Open (NO)
Momentarily close to run
forward Normally Closed
(NC)
Momentarily open to
stop Normally Open (NO)
Momentarily close to
run reverse O: Preset speed 1
C: Keypad mode Up and Down buttons
can be used to set the
speed when analog
input is set to keypad
mode.
18 O: Stop (Disable)
C: Run (Enable) Open Open O: Terminal mode
C: Keypad mode Preset speed 1
Closed Open Preset speed 2
Open Closed Preset speed 3
Closed Closed Preset speed 4
19 O: Stop (Disable)
C: Run (Enable) O: Analog input
C: 2nd analog input 2nd analog input Bipolar analog
input –
20 O: Stop (Disable)
C: Run (Enable) 2nd digital output
(+24 V) O: Analog input
C: Preset speed 1 Bipolar analog
input 2nd digital output
shows drive healthy
21 O: Stop (Disable)
C: Run (Enable) 2nd digital output
(+24 V) O: Forward
C: Reverse Bipolar analog
input 2nd digital output
shows drive healthy
22 O: Stop (Disable)
C: Run (Enable) 2nd digital output
(+24 V) External trip input:
O: Trip
C: OK Bipolar analog
input 2nd digital output
shows drive healthy
P2-01 Digi input 1 (DI1) Digi input 2 (DI2) Digi input 3 (DI3) Analog input (AI) Comments / Preset
value
NOTE
When P2-01 = 20, the 2nd digital input is configured as an output, which o24 V
when the drive is healthy. If the drive is not healthy, the output will be 0 V.
When connecting a motor thermistor, connect it between terminals 1 and 4.
Set P2-01 to 6, 10, 11, 12 or 22 (uses external trip input).
P6..
P60.
P600