Selden Furlex 100 S Скачать руководство пользователя страница 44

Страница: 44 / 52

Always use a strong ”D” shackle or tie the halyard.

1. Slacken the

backstay

as much as possible, but make sure that any rigging screw is not unscrewed

so far that the threads are no longer visible ”on the inside”.

2. Pull the masthead forward using the genoa halyard. Secure the halyard using a ”D” shackle or tie

it to a strong deck fitting. Do not use the halyard snap shackle for safety reasons.

3. Tie a strong, flexible line around the luff extrusion. Make two clove hitches ,the upper approx. 1 m

(39 3/8”) from the top, taping over the knots so that they cannot slide.

4. Hoist the stay using a spare halyard.

5. ”Go aloft” and attach the top end of the Furlex system to the forestay attachment. Always use a

proper bosun’s chair. If there are no free headsail halyards use the main halyard. For further

information, see Seldén Mast AB’s ”Hints and Advice” on ”Working aloft” or contact your Furlex

dealer.

6. Attach the stay to the headbox, then to the deck fitting. The split pin for the

clevis pin should be opened by ~ 20°. It will then retain its shape on

dismantling, enabling it to be used again.

Rigging screw:

Adjust the forestay to the desired length. (See chap. 14.1).

8. Tension the forestay to 20% of the wire’s breaking load. As the tension on the forestay cannot be

measured easily when it is encased in the luff extrusion, this can be done using the backstay.

Owing to the difference in the angle of these stays relative to the mast, this is on a Masthead rig

equivalent to approx. 15% of the backstay’s breaking load, assuming that it is the same diameter as

the forestay. (Forestay tension = approx. 1.25 x backstay tension.)

A firmly tensioned stay offers the least furling resistance.

For further information, see Seldén Mast AB’s ”Hints and Advice” or contact your Furlex dealer.

Fig. 16.1.a

Fig.16.1.b

16.1 Fitting the Furlex on a stepped mast

The Furlex system is best transported and rigged together with the mast.

16 Rigging

Содержание Furlex 100 S





















































Результаты поиска

Содержание Furlex 100 S

Отзывы:

Похожие инструкции для Furlex 100 S

Бренды по названию

Популярные бренды

Selden Furlex 100 S, Руководство пользователя

Результаты поиска

Содержание Furlex 100 S

Отзывы:

Похожие инструкции для Furlex 100 S

Бренды по названию

Популярные бренды