Selden Furlex 100 S Скачать руководство пользователя страница 13

Страница: 13 / 52

Deduction for lower wire terminal:

Ø 4 mm wire: – 45 mm (1 3/4”)

Ø 5 mm wire: – 55 mm (2 5/32”)

Ø 6 mm wire: – 70 mm (2 3/4”)

Existing forestay length (FL), including rigging screw (See fig. 3.5.a)

Furlex fitted above deck, but with the forestay fitting

in the anchor well.

Use the Furlex extension toggle. For a larger gap, use

a custom-made stainless steel bar or rod stay. For Ø 6

only, the Furlex rigging screw or extension link may

also be used.

Short wire pendants are not recommended as forestay

forces may not be distributed evenly, and wire will not

resist the torque which may be produced.

1. Determine the rake of the mast with the fore-/backstay tensioned.
2. Slacken the

backstay

as much as possible, but make sure that any rigging screw is not unscrewed

so far that the threads are no longer visible ”on the inside”. The forestay setting should not be

adjusted. If there is insufficient adjustment in the backstay, and the forestay must be adjusted to allow

removal, first mark its thread with adhesive tape.
3. Pull the masthead forward using the genoa halyard. Secure the halyard using a ”D” shackle or tie it

to a strong deck fitting. For safety reasons, do not use the halyard snap shackle.

Always use a strong ”D” shackle or tie the halyard!

4. Take down the forestay. If it was slackened, adjust the rigging screw back to the tape marks.
5. Measure the forestay length (FL)

with just enough tension to keep it straight.

6. Enter the measurement in

Calculation Table 1

below, under the heading ”Your forestay”, in the row

marked FL.
7. Calculate the new wire length WL in Table 1. Refer to the column marked ”example” to see how

this is done.

Your

forestay

Example

Ø5

Table1: Calculation of forestay wire length

3.5.1

If a Furlex rigging screw (Ø 6 mm forestay only), links or extra toggles

are to be used, deduct this length (H) from FL.

Cutting measurement. The new forestay wire is to be marked

at this point.

190

13100

Fig. 3.4 d.

9.675

9.620

3.5 Calculating the length of the forestay wire

Содержание Furlex 100 S





















































Результаты поиска

Содержание Furlex 100 S

Отзывы:

Похожие инструкции для Furlex 100 S

Бренды по названию

Популярные бренды

Selden Furlex 100 S, Руководство пользователя

Результаты поиска

Содержание Furlex 100 S

Отзывы:

Похожие инструкции для Furlex 100 S

Бренды по названию

Популярные бренды