Seeley coolair Braemar Breezair MaglQcool Скачать руководство пользователя страница 34

Страница: 34 / 68

MAGIQTOUCH & MAGIQCOOL MODELS

CONFIGURATION OF DRAIN VALVE WITH

SHORTING PLUG
Note!

This procedure is not backward

compatible for 2001 CPMD’s and is only an aid

to installation.

A shorting plug should be fitted to the cooler

electronics box of coolers that do not have a

drain valve installed (i.e. those with bleed tray).
The shorting plug must be inserted before

power is applied to the cooler electronics. At

power on the electronics recognises the water

probes are not connected and automatically

operates as “NO DRAIN CONTROL”.

Note!

This will override what has been set in

the MagIQtouch Controller SETTINGS menu.
If the shorting plug is removed whilst power is

on, the change will not be noticed by the cooler

electronics until the next power on, when

parameters will be automatically changed.

ILL1430-C

BRAEMAR

Correct Plug Orientation

ILL1858-A

If an existing LCQ/LCS cooler requires the

drain and solenoid valve to be removed, and

you are not certain it will accept the shorting

plug, the water management parameter can be

set manually using the MagIQtouch Controller.
Go to the SETTINGS menu, and under

the COOLER heading is the option “Water

Manager”.

COOLER ELECTRONICS

The Red LED (right-hand LED) is used to

indicate the condition of water salinity and

configuration of the water management

system. Tri-Colour LED (left-hand LED) is used

as an operational and fault indicator.

Note!

Tri-colour LED double flashing Green

(every 2 seconds) = Normal Operation

LEGEND

A -   Controller Cable
B -  Speed Adjustment
C -   Inlet Solenoid
D -   Water Sensor

LEGEND

A - Circuit Breaker
B - Mains Connector

ILL1062-G

ILL1412-B

Common

Run

Start Earth

Ensure that connection orientation is correct.

Note!

Controller cable (A) used in MagIQtouch

compatible products is different to previous

models and is NOT interchangeable.

CAUTION!

It is possible to insert plugs up-

side-down or to misalign the connections. Care

must be taken to ensure correct orientation

and alignment.

E -   Drain Valve
F -   Pump
G -   Operation & Fault code LED’s

C - Motor (240Vac)

(Seelectric Motor Only)

BRAEMAR LCQ / LCS / BMQ &

COOLAIR CPQ EVAPORATIVE

COOLER

cont

Содержание coolair Braemar Breezair MaglQcool





































































Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды

Seeley coolair Braemar Breezair MaglQcool, Руководство по обслуживанию

Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды