Seeley coolair Braemar Breezair MaglQcool Скачать руководство пользователя страница 19

Страница: 19 / 68

SEELEY INTERNATIONAL

- SERVICE GUIDE

MANAGING FAULTS

cont

ILL1628-C

ILL1629-C

Component

Status Resulting Action

Pump

Tornado pump active,

water pumping over pads

OFF

Pump off

Solenoid

Solenoid open

(water filing tank)

OFF

Solenoid closed

Drain

Drain closed (energised)

OFF

Drain open

For multi-cooler installations, all other coolers

except the cooler being displayed will continue

to operate as they were at the time of entering

the ‘Service Operating Screen’. Other coolers

of the same type can be accessed from the

‘Service Operating Screen’ quickly, by using

the scroll left/right buttons.

Important!

When a new cooler is selected, the

previously displayed cooler will return to the

operation state that was occurring at the time

of entering the ‘Service Operating Screen’.

COOLER ELECTRONICS BOX

Fault diagnostics can also be accessed from

the cooler electronics box itself.

The ‘Service Operating Screen’ for evaporative

coolers allows the service agent to:

• Turn the cooler ON or OFF

• Set the fan speed

• Turn the pump, solenoid or drain valve ON or OFF

MANAGING COMPONENTS

ADDING COMPONENTS

The controller keeps a list of all the

MagIQtouch installed components and

regularly checks that all components are

responding.
To add a new component, simply connect it to

the system and power up. The controller will

detect that a new component has been added

and lead you through the set-up process.

Important!

It is important that new

components of the same type are connected

ONE AT A TIME.

Below are a list of MagIQtouch compatible

components.

ILL1633-A

Component

Part

No.

Air Sensor

094328

Link Module, Board only

094281

Link Module including enclosure

094724

Zone Control Board 240V, Board only

(used with TQ heaters)

094922

Zone Control Board 24V, Board only

(used with TQ heaters)

094939

Zone Control Board 240V with

Enclosure (used with TQ heaters)

094908

Zone Control Board 24V with Enclosure

(used with TQ heaters)

094915

MagIQtouch Controller with cable (used

as Slave with TQ heaters)

075587

AOC - SACV10D1S IDU 10kW 1PH INV 085807
AOC - SACV12D1S IDU 12kW 1PH INV 085814
AOC - SACV14D1S IDU 14kW 1PH INV 085821
AOC - SACV16D1S IDU 16kW 1PH INV 085838

For more details refer to “DIAGNOSTICS

FAULT CODES” within the Breezair (pg 23)

and Braemar (pg 33) cooler sections of this

document.

Содержание coolair Braemar Breezair MaglQcool





































































Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды

Seeley coolair Braemar Breezair MaglQcool, Руководство по обслуживанию

Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды