Seeley coolair Braemar Breezair MaglQcool Скачать руководство пользователя страница 39

Страница: 39 / 68

SEELEY INTERNATIONAL

- SERVICE GUIDE

BRAEMAR LCQI EVAPORATIVE

COOLER

cont

• Debris interfering with water sensor probes.

• Probes not clipped onto mounting brackets

correctly.

• Check cooler is level and water drains quickly.

FAULT CODE 07 (7 Red Flashes)
Motor error

WARNING: Motor/Fan could re-start without

warning as the controller attempts to re-

start the motor within 30 seconds of initially

failing this Fault Code.

•

Ensure the motor power cable is fitted correctly to

the control electronics.

•

Ensure the motor communication cable is fitted

correctly to the control electronics

•

FAULT CODE 08 (8 Red Flashes)
Supply Voltage error

WARNING: Motor/Fan could re-start without

warning as the cooler will re-start should

the voltage return to normal.

• Fan shuts down when supply voltage drops below

93V.

SALINITY LED

The Red LED (right-hand LED) is used to

indicate the condition of water salinity and

configuration of the water management

system. Parameters are set by MagIQtouch or

MagIQcool wall controllers. Refer to pages 17

or 21 of the service manual.

Salinity LED Indication for evaporative coolers

fitted with drain valves.

Sal Flash

Indicates

OFF

Not Applicable

1 Flash

WaterMiser

salinity is below the

set point.

2 Flash

WaterMiser

salinity is above the

set point.

3 Flash

The Salinity Control Method is set

for Timed Drain

4 Flash

Bleed Tray - No Drain Valve.

5 Flash

Thermostatic Control (no Water)

operation set.

Continuously

(When probes

immersed in

water)

Water not detected. The probes

are immersed in water but are

open circuit, or measured salinity

is less than 20µs/cm (the water

has very little salt content).

Continuously

(No water in

tank)

WaterMiser

/ Drain Valve option

is active

ILL2130-A

COMPONENT COMPATIBILITY WITH

OTHER SEELEY COOLERS
Note!

Drain Valves, Water Management

Probes and Solenoids used in EXQ/LCQ/BMQ/

CPQ products are different to those used in the

LCQI models and are NOT interchangeable.
Refer to the table shown on Page page 38

for correct part numbers for LCQI Spares

items.

Содержание coolair Braemar Breezair MaglQcool





































































Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды

Seeley coolair Braemar Breezair MaglQcool, Руководство по обслуживанию

Результаты поиска

Содержание coolair Braemar Breezair MaglQcool

Отзывы:

Похожие инструкции для coolair Braemar Breezair MaglQcool

Бренды по названию

Популярные бренды