manualshive.com logo in svg

SBC PCD2.M5 Series, Руководство пользователя


Поделиться
Скачать
background image

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Memory module PCD3.R600 for flash cards (FCs)

PCD2.M5_ Classic CPUs and expansion housings

3-44

3

3.13.3 Operation 

The PCD2.R6000 can only be inserted into I/O slot 0...3 (0, 16, 32, 48) on a 

PCD2.Mxxxx. The firmware detects these modules at start-up and installs the 

necessary drivers. Do not insert or remove the modules with the power on. 

Up to 4 PCD2.R6000 units can be used in a PCD2 system.

Insertion of I/O modules

The I/O modules are inserted from the side, pushed towards the middle of the unit 

until they reach the end stop and snap into the retaining catch.

Retaining clip

Bus connector

A2

A1

I/O-sockets

C

PCD2.M5540

0

3

2

1

7

4

5

6

Data access

Browser 

FTP-Client 

Explorer 

FTP-Server 

Web  

pages 

Any  

data/files 

Flash memory with file system 

PCDx.R55xM04, PCD2.R6000

(4 Mbyte - 1 GByte max.)  

User program, 

Web pages 

Onboard memory,  

and PCD7.R500  

  

for backup 

(512 kByte max.) 

Web-Server 

PG5 

Ethernet-TCP/IP 

User program 

with new CSF, 

SFB instruc- 

tions  

PCD data 

memory 

DB/X, R, F, ... 

PCD2.Mxxxx

FTP server and file system access can only be achieved with the plug-in flash 

memory module. Access via FTP server is only possible via the Ethernet TCP/IP 

interface.

Based on the predefined requirements, SBC uses its own file system. The SBC file 

system is embedded in a FAT (PC compatible file system) framework, to make the 

restricted processes when used in a commercial SD card reader/writer visible with 

Содержание PCD2.M5 Series





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCD2.M5 Series

Valve Concepts 5400 Installation, Operation And Maintenance Manual preview
5400
Бренд: Valve Concepts Страницы: 16
Febco 860 Series Installation Instructions preview
860 Series
Бренд: Febco Страницы: 4
Cisco Catalyst 3110G Hardware Installation Manual preview
Catalyst 3110G
Бренд: Cisco Страницы: 48
Panasonic CZ-RTC5B Installation Instructions Manual preview
CZ-RTC5B
Бренд: Panasonic Страницы: 15
Panasonic CZ-RTC3 Operating Instructions Manual preview
CZ-RTC3
Бренд: Panasonic Страницы: 42
Warren Controls E024 Installation, Operation And Maintenance Instructions preview
E024
Бренд: Warren Controls Страницы: 28
EAS Electric ECRP86EKD Operating Manual preview
ECRP86EKD
Бренд: EAS Electric Страницы: 89
HandyTrac Key Control Easy Manual Installation And Operation preview
Key Control
Бренд: HandyTrac Страницы: 14
TA STA Quick Start Manual preview
STA
Бренд: TA Страницы: 6
Parker A4W Series Installation And Service Information preview
A4W Series
Бренд: Parker Страницы: 12
VAT 264 Series Installation, Operating, & Maintenance Instructions preview
264 Series
Бренд: VAT Страницы: 26
cinetto PS40.3 Assembly Instructions Manual preview
PS40.3
Бренд: cinetto Страницы: 56
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Бренд: I-Tork Страницы: 15
MGC RAXN-LCD Installation And Wiring Manual preview
RAXN-LCD
Бренд: MGC Страницы: 16
Aruba S3500 Series Uplink Module Installation Manual preview
S3500 Series Uplink Module
Бренд: Aruba Страницы: 8
Lutron Electronics FS-5F Easy-To-Follow Instructions preview
FS-5F
Бренд: Lutron Electronics Страницы: 2
IDEATEC DLC4000 User Manual preview
DLC4000
Бренд: IDEATEC Страницы: 32
Broadcast Tools AVR-8 Installation And Operation Manual preview
AVR-8
Бренд: Broadcast Tools Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды