SBC PCD2.M5 Series Скачать руководство пользователя страница 156

Страница: 156 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Multi-functional input/output modules

Input/output (I/O) modules

6-45

6.7.1 PCD2.G400, multi-functional input/output module

Application

Combined module with digital and analogue inputs and outputs. This module is

designed to extend the range of uses for the PCD. The functions and the technical

specification are based on the existing PCD2 modules.

The technical details should be taken from the descriptions of these modules.

Number and type of inputs/outputs
10 digital inputs,

E0…E9 (addresses 0…9)

Technical data as for PCD2.E110, but without the option of sink operation

option,

i.e. no “L” connection.

6 analogue outputs,

O16…O21 (base address 16, channels 0…5)

…

10 V

/ 8 bit, other tech. details as for PCD2.W400.

8 digital outputs,

O32…O39 (addresses 32…39)

24 V

/ 0.5 A; remaining tech. data as for PCD2.A400.

2 analogue inputs,

I48 and I49 (base address 48, channels 0…1)

…

10 V

/ 10 bit, other tech. details as for PCD2.W400.

6 analogue inputs,

I50…I55 (base address 48, channels 2…7)

Pt/Ni 1000 / 10 bit with data as for PCD2.W220.

Internal current consumption from +5 V bus:

…

65 mA

V+

Bus: 35

LEDs and connection terminals

---- ----

A16

----

A17 A18 A19 A20 A21 ----

A32 A33 A34 A35 A36 A37 A38

----

A39

E48 E49 E50 E51 E52 E53 E54 E55 ---- ----

E110

W400

A400

W200 / W220

The module can be installed on sockets 1…4 (top) on the PCD2.

Содержание PCD2.M5 Series





















































































































































































































































Результаты поиска

Содержание PCD2.M5 Series

Отзывы:

Похожие инструкции для PCD2.M5 Series

Бренды по названию

Популярные бренды

SBC PCD2.M5 Series, Руководство пользователя

Результаты поиска

Содержание PCD2.M5 Series

Отзывы:

Похожие инструкции для PCD2.M5 Series

Бренды по названию

Популярные бренды