SBC PCD2.M5 Series Скачать руководство пользователя страница 153

Страница: 153 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Digital combined input/output modules

Input/output (I/O) modules

6-42

General technical data on inputs and outputs

Resistance to interference:

acc. to IEC 801-4

4 kV under direct coupling

2 kV under capacitive coupling (whole trunk group)

Internal current consumption:

(from +5 V bus)

…

25 mA

typ. 15 mA

Internal current consumption:

(from V+ bus)

0 mA

External current consumption:

Load current

Terminals:

Pluggable 10-pole screw terminal block (4 405 4847 0), for

wires up to 1.5 mm²

LEDs and connection terminals

Input filter

Recovery diodes

LEDs

Screw terminals

Bus connector

Bus interface

Output transistors (MOSFET)

The module contains 8 LEDs:

●  2 LEDs are directly triggered by the pure inputs.
●  2 LEDs are directly triggered by the pure outputs.
●  4 LEDs are triggered by the inputs of the combined inputs/outputs and therefore

always indicate voltage status at the I/O terminal.

If the combined I/Os are used as outputs, the following should be noted:

The LEDs of combined outputs I/O2...I/O5 only light up when the output is high and a

supply voltage of 24 V is connected to Uext.

Mixing the combined inputs/outputs

If combined I/Os are used as inputs in source operation, i.e. with sending devices which

either apply +24 V to the input or are open, the low status of an open input can be overwrit-

ten as high if the corresponding output at the same address is set in error. However, if the

input is shifted to 0 V with a changeover contact and the corresponding output is set in error,

the MOS-FET can be destroyed, as it is not short circuit protected. For this reason, only

positive-switching contacts should be used.

Содержание PCD2.M5 Series





















































































































































































































































Результаты поиска

Содержание PCD2.M5 Series

Отзывы:

Похожие инструкции для PCD2.M5 Series

Бренды по названию

Популярные бренды

SBC PCD2.M5 Series, Руководство пользователя

Результаты поиска

Содержание PCD2.M5 Series

Отзывы:

Похожие инструкции для PCD2.M5 Series

Бренды по названию

Популярные бренды