manualshive.com logo in svg

SBC PCD2.M5 Series, Руководство пользователя


Поделиться
Скачать
background image

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

E-display with PCD7.D3100E nano-browser

PCD2.M5_ Classic CPUs and expansion housings

3-66

3

3.19.7 Web-Editor

Web-Editor Version

At least Version 5.14.23 or higher is necessary to start with the eDisplay with Firm

-

ware 51. Reduced eDisplay functionality is available with delivered license key.

Specific Project Settings for eDisplay

This software version integrates new functionalities which are essential for the good 

implementation of a project for the eDisplay

 

Default Fonts, Fonts and Font generator

Default Fonts:

 

The two default fonts and size are: 

- Tahoma regular 8 

- Tahoma regular 12 

These fonts can be used in all cases, for PPOs, Containers, Strings or html tags.

Font generator 

The use of other character sets and font sizes is possible with the font generator, 

which has been incorporated in this version. The relevant .fnt files are created auto

-

matically during the Web-Editor’s «build». 

Project configuration: 

Содержание PCD2.M5 Series





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PCD2.M5 Series

Handicare VR2 User Manual preview
VR2
Бренд: Handicare Страницы: 56
Hardi HC5500 Quick Manual preview
HC5500
Бренд: Hardi Страницы: 2
YASKAWA CC-Link Technical Manual preview
CC-Link
Бренд: YASKAWA Страницы: 64
V2 Phoenix Programming Manual preview
Phoenix
Бренд: V2 Страницы: 3
Daikin BRC1E61 Operation Manual preview
BRC1E61
Бренд: Daikin Страницы: 56
Danfoss ERC 211 User Manual preview
ERC 211
Бренд: Danfoss Страницы: 36
Federal Signal Corporation UltraVoice Installation, Operation And Service Manual preview
UltraVoice
Бренд: Federal Signal Corporation Страницы: 60
FASTRON. VC-210 Installation And Operating Instructions Manual preview
VC-210
Бренд: FASTRON. Страницы: 16
IBM ServeRAID-MR10is User Manual preview
ServeRAID-MR10is
Бренд: IBM Страницы: 94
IBM ServeRAID-4 Ultra160 Series Installation Instructions Manual preview
ServeRAID-4 Ultra160 Series
Бренд: IBM Страницы: 20
IBM 8271 Nways Ethernet LAN Switch Manual preview
8271 Nways Ethernet LAN Switch
Бренд: IBM Страницы: 6
IBM 3174 Introduction Manual preview
3174
Бренд: IBM Страницы: 86
IBM 3745 Series Console Setup Manual preview
3745 Series
Бренд: IBM Страницы: 205
IBM N6000 Series Installation And Setup Instructions preview
N6000 Series
Бренд: IBM Страницы: 28
Parker CHELSEA Owner'S Manual preview
CHELSEA
Бренд: Parker Страницы: 32
Rayrun NT30 Quick Start Manual preview
NT30
Бренд: Rayrun Страницы: 4
PACH & COMPANY AeGIS 7000 Series Quick Start Manual preview
AeGIS 7000 Series
Бренд: PACH & COMPANY Страницы: 2
Vacon 100 HVAC User Manual preview
100 HVAC
Бренд: Vacon Страницы: 50

Бренды по названию

Популярные бренды

Загрузить еще бренды