Sanyo VCC-HD5400 Скачать руководство пользователя

Страница: 9 / 145

The terminal outputs super-fine HD (High Definition) video signal. Use the terminal to connect a high-definition
monitor with HDMI interface.

To record live video on a SD memory card, open the cover as shown below and insert the card into the card slot

until you hear a click.

Fall-prevention screw

Use this screw and the supplied hexagonal wrench to secure the installed camera.

SD Card Slot

Power indicator

This indicator lights up when the camera is powered on.

When the camera is on, this indicator blinks to indicate the following camera statuses:

Deactivation of recording to SD memory card in progress

Firmware update in progress

An SD memory card error occurred (Fast blink)

SD CARD button

Disable recording: The power indicator blinks when this button is pressed, and stays lit when the SD memory
card is prepared to be removed.

Enable recording: The power indicator blinks when this button is pressed, and stays lit when the SD memory
card is recognized.

Use this cable to hook the camera on the supplied mounting plate when installing the camera.

Perform the following connections according to the installation environment and application of your camera.

Power Connection

Network Connection

Alarm Cable Connection

Connection of system controller

Installing Recording Media

Before attempting the following connections, be sure to turn off all components of your system.

Improper connection may cause smoke or failures. Before attempting to connect each system

component, carefully read the instruction manual that comes with it to familiarize yourself with the
correct connection procedure.

Introduction 9/15

Содержание VCC-HD5400


















































































































































Результаты поиска

Содержание VCC-HD5400

Отзывы:

Похожие инструкции для VCC-HD5400

Бренды по названию

Популярные бренды

Sanyo VCC-HD5400, Руководство пользователя

Результаты поиска

Содержание VCC-HD5400

Отзывы:

Похожие инструкции для VCC-HD5400

Бренды по названию

Популярные бренды