SANCH S3800C Series, Руководство пользователя

Страница: 94 / 105

９１
0: Invalid
1: Valid Action (Customizable logic
１０． ００
10 Application function 3 parameters
Control Method
Setting Range
V/f
Wit-
hout
PG
PG
V/f
PG
Para-
meter
Parameter
Functions
Fact-
ory
Defa-
ult
Torque
control
× ○ ○ ○ ○
Customizable Logic
(Mode selection)
０
０
○ ○ ○
０ ○ ○ ○ ○
○
○
×
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○ ○
○ ○ ○ ○
○ ○
×
× × ×
○ ○
× × ×
○ ○
×
×
○ ○ ○ ○ ×
○ ○ ○ ○ ×
○ ○ ○ ○
×
○ ○ ○ ○
×
○ ○
×
×
○ ○ ○ ○ ×
○ ○ ○ ○
×
× ×
× ×
１０． ０１
Customizable Logic:
(Input 1) step 1
0(1000): Inverter running [mRUN]
2(1002): Frequency (speed) detection [mFDT]
3(1003): Undervoltage detected(When Inverter
stopped) [mLU]
4(1004): Torque polarity detection [mB/D]
5(1005): Inverter output limiting [mIOL]
6(1006): Auto-restarting after momentary
power failure [mIPF]
7(1007): Motor overload early warning [mOL]
8(1008): Keypad operation enabled [mKP]
10(1010): Inverter ready to run [mRDY]
11: Switch motor drive source between
commercial power / inverter output [mSW88]
12: Switch motor drive source between
commercial power / inverter output [mSW52-2]
13: Switch motor drive source between
commercial power / inverter output [mSW52-1]
15(1015): AX terminal function [mAX]
16(1016): Simple PLC operation conversion
section signal [mTU]
17(1017): Simple PLC operation cycle
completion [mTO]
18(1018): Simple PLC sections instruction
No.1 [mSTG1]
19(1019): Simple PLC sections instruction
No.2 [mSTG2]
20(1020): Simple PLC sections instruction
No.4 [mSTG4]
22(1022): Inverter output limiting ( with delay )
[mIOL2]
25(1025): Cooling fan ON-OFF in operation
[mFAN]
26(1026): Auto-resetting [mTRY]
28(1028): Cooler overheat early warning [mOH]
29(1029): SY synchronization completed [mSY]
30(1030): Lifetime alarm [mLIFE]
31(1031): Frequency (speed) detection 2
[mFDT2]
33(1033): Reference loss detected [mREF OFF]
35(1035): Inverter output on [mRUN2]
36(1036): In overload prevention control[mOLP]
37(1037): Current detected [mID]
38(1038): Current detected 2 [mID2]
39(1039): Current detected 3 [mID3]
41(1041): Low current detected [mIDL]
42(1042): PID alarm output [mPID-ALM]
○ ○ ○ ○ １０． ０２
Customizable Logic:
(Input 2) step 1
1(1001): Frequency (speed) arrival signal
[mFAR]