NOTE: When your keyset is programmed for Auto Answer and you have For-
ward No Answer (FNA) turned on, you must answer screened transfers by
pressing the
ANS/RLS
or the
MONITOR
key if you are using a 7B phone
before your FNA timer expires or the call will forward.
AUTOMATIC HOLD
While on an outside call, pressing a line key, route key or a flashing
CALL
button will automatically put your call on hold and connect you to the next
call. This feature can be turned on or off at your keyset.
•
With the handset on-hook, press
TRF
and then dial
110
.
•
Dial
001
to turn Automatic Hold on or
000
to turn it off.
•
Press
TRSF
to store your selection.
NOTE: Intercom calls can be automatically put on hold by pressing
TRSF
.
HEADSET OPERATION
Keyset users can switch between headset mode and handset mode. When
using headset mode, press the
ANS/RLS
or the
MONITOR
key if you are
using a 7B phone to answer and release calls.
•
With the handset on-hook, press
TRSF
and then dial
110
.
•
Dial
021
to use the headset or
020
to use the handset.
•
Press
TRSF
to store your selection.
Your keyset may be equipped with a Headset mode key. If it is so equipped
pressing this key while the light is out will cause the keyset to enter headset
mode and the light will illuminate to indicate this. Pressing the key while the
light is lit will cause the keyset to return to handset mode and the light will
go out.
HOT KEYPAD
On your phone system your keyset’s keypad can be made “live” or “hot” so
that it is not necessary to lift the handset or press the
SPK
or the
MONITOR
key before you begin dialing. Calls can be made and features activated by
simply dialing the C.O. line number, trunk group access code, intercom
number or feature access code. To activate this feature:
•
With the handset on-hook, press
TRSF
and then dial
110
.
•
Dial
031
to turn the Hot Keypad on or
030
to turn it off.
•
Press
TRSF
to store your selection.
39
38
CUSTOMIZING YOUR KEYSET
AME PASSWORD
This feature allows people using the AME (Answer Machine Emulation) fea-
ture to enable password protection. This will prevent unauthorized people
from listening to your messages being left. The passcode is the same as
your station passcode. This feature only applies if there is a Samsung Voice
Mail card installed in the system and your keyset has a programmed AME
key.
See Keyset User Features in SVMi-4/SVMi-8 section.
•
With the handset on-hook, press
TRSF
and then dial
110
.
•
Dial
101
to turn on AME PASSCODE or
100
to turn it off.
•
Press
TRSF
to store your selection.
SELECT RING TONE
Each keyset user can select any one of eight ring frequencies:
•
While on-hook, press
TRSF
and then dial
111
.
•
Dial
1
–
8
or press the
UP
and
DOWN
keys to hear each tone.
•
When you hear the tone that you prefer, press
TRSF
to save it.
NOTE: Specific lines or stations may be programmed to ring with a dif-
ferent tone than what you have selected for your keyset.
CHANGE YOUR PASSCODE
From the factory, your station passcode is 1234. You can change your sta-
tion passcode whenever you desire.
•
While on-hook, press
TRSF
and then dial
101
.
•
Dial your old passcode.
•
Dial a new passcode (must be four characters). You can use
0
–
9
.
•
Redial the new passcode to verify. If successful, you will hear two beeps.
Four beeps indicate an incorrect code. Reenter the code again.
•
Press
TRSF
to store the new passcode.
SET ANSWER MODE
You can receive internal calls in one of three modes
•
While on-hook, press
TRSF
and then dial
103
.
•
Dial
0
for Ringing,
1
for Auto Answer or
2
for Voice Announce.
•
Press
TRSF
to store your selection.
HOME PAGE
Table of Contents
Guide-Contents
