Samsung DW80M9* Series Скачать руководство пользователя

Страница: 5 / 62

Safety Instructions _ 3

Caution

Before Servicing

ࣃ

Do not sprinkle water onto the dishwasher directly when cleaning it.

- This may result in electric shock or fire, and may shorten the product life.

ࣃ

Do not place any containers with water on the dishwasher.

- If the water is spilled, it may result in electric shock or fire.

This will also shorten the product life.

ࣃ

Do not install the dishwasher in a location exposed to snow or rain.

- This may result in electric shock or fire, and shorten the product life.

ࣃ

Do not press a control button using a sharp tool or object.

- This may result in electric shock or damage to the product.

During Servicing

ࣃ

When connecting a wiring harness, make sure to seal it completely so no liquid can enter.

- Make sure that the connections are secured by slightly pulling on them.

ࣃ

Check if there is any evidence that liquid has entered electric components or connections.

- If any liquid has entered into a part, replace it or completely remove any remaining moisture from it.

ࣃ

If you need to place the dishwasher on its back for servicing purposes, place a support(s) on the floor and lay it

down carefully so the back is on the floor.

- Do not lay it down on its front or side. This may result in scratches to the surface or damage to the parts.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды