Samsung DW80M9* Series Скачать руководство пользователя

Страница: 37 / 62

Troubleshooting_35

Check

code

Display

Check

code

Recall

When occur

Symptom

Possible Causes

No display

HC1

- The start temperature is saved 30 seconds after heating starts.

Thereafter, if the temperature change is equal to or less than 4

℃

for 10 minutes, the heater relay is turned off for 1 second and

then restarts heating. Then, if the temperature change is equal

to or less than 4

℃

for 10 minutes again, an HC1 check code

occurs.

- Keep going remained cycle with heater off

condition.

- The heater is out of order.

- The heater is improperly connected.

- When the temperature is measured as equal to or greater than

℃

for 3 seconds.

- The driving part stops and the main relay is

turned off.

- The heater is out of order.

- The thermistor is out of order.

No display

bC2

- When the button is pressed and held for 30 continuous seconds

or longer.

- Keep going remained cycle

- The touch button is out of order.

- An object is on the touch button.

No display

bC3

- When IC communications between the Sub PBA and the touch

button fails.

- Keep going remained cycle

- The touch button is out of order.

- The sub PBA or touch button PBA is not

properly connected.

No display

- When communications between the main PBA and the sub PBA

fails for 24 seconds.

(In Test Mode, communication fails for 6 seconds.)

- Keep going remained cycle

- The main PBA or sub PBA is out of order.

- The communications connection for the

main PBA or sub PBA is not properly

connected.

No display,

change to

pause

AC6

- When the response is not received from inverter PBA for 3

seconds, Inverter RELAY OFF for 2 minutes.

After repeated 3 times, display the check code

- Inverter Relay 2min off, 3sec on(until find

response)

- Display change to pause

- The main PBA or Inverter PBA is out of

order.

- The communications connection for the

main PBA or Inverter PBA is not properly

connected.

- When the water leakage sensor data is equal to or less than 3V

for 3 seconds.

- Main relay off.

- If sensor data over 3V is detected after draining

(20 seconds on/5 seconds off) is performed for

3 minutes, the drain pump is turned off. If data

over 3V is detected, draining is performed for 3

minutes and then the sensed data is checked

again.

- There is a water leak.

- When the overflow sensor data is equal to or less than 3V for 5

seconds.

- If check code has occurred when set operating,

3times ‘3min drain’ retry, and display “OC” (No

operating condition, display “OC” without retry)

- During retry 3times, display ‘pause’

- The case brake fails to detect the pulse.

- The valve water is out of order.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды