Samsung DW80M9* Series Скачать руководство пользователя

Страница: 54 / 62

52 _ Troubleshooting

Check type

Check code

Checking method

Corrective actions

Detergent

is not

dispensed

None

1. Check whether detergent is inserted into the dispenser.

- Check whether there is detergent in the Dispenser.

2. Check the connections for the Dispenser connector.

- Reconnect the Dispenser connector.

3. Check the resistance of the Dispenser.

(Remove the connector before measuring.)

► Normal: Approx. 0.7 ~ 3kΩ

- Faulty: Replace the Dispenser.

4. Check the operation of the Dispenser Relay

: Check the operating voltage between the Black wire of the CN401

connector and the White wire of the CN101 connector.

► Normal: 110V ~ 120V (while operating)

- Faulty: Replace the Main PBA Assy.

No washing

None

1. Check the filter

- Faulty: Replace filter

2. Check Rotors and ducts and vane

- Faulty: Replace Rotors and ducts

3. Check the operation of the half load.

- See “PC check code”.

4. Check the operation of the Dispenser

- See “Dispenser is not dispensed”.

The cycle does

not start.

None

1. Check the connections for the Door Sensing Switch

: Check the white wire and the switch connected to the white wire.

► Normal: 10.5 to 13V (when the door is open)

► Normal: < 1V (when the door is closed)

- Reconnect the Door Sensing Switch Connector

2. Check the connection for the Door Sensing Switch.

- Reconnect the Door Sensing Switch Connector

3. Check the operation of the Door Sensing Switch.

(Remove the connector before measuring.)

: Check the blue wire and the switch connected to the blue wire.

► Normal: SHORT(when the door is open)

► Normal: OPEN (when the door is closed)

- Faulty : Replace the Door Sensing Switch.

4. Check the operation of the Power Relay.

- Normal : Replace the Main PBA Assy.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды