Samsung DW80M9* Series Скачать руководство пользователя

Страница: 4 / 62

2 _ Safety Instructions

While Servicing

ࣃ

Check if the power cable is damaged, flattened, cut or otherwise degraded.

- If faulty, replace it immediately. Failure to do so may result in electric shock or fire.

ࣃ

Completely remove any dust or foreign material from the housing, wiring and connection parts.

- This will prevent a risk of fire due to arcing and short circuits in advance.

ࣃ

When connecting wires, make sure to connect them using the correct connectors and check that they are

completely connected.

- If tape is used instead of the connectors, it may cause fire due to arcing.

ࣃ

Make sure to disconnect the PBA power terminals before starting the service.

- Failing to do so may result in a high voltage electric shock.

After Servicing

ࣃ

Check for any water leakage.

- Perform a test using the standard(normal) cycle and check whether there is any water leakage through the floor

section or the pipes.

ࣃ

Do not allow consumers to repair or service any part of the dishwasher themselves.

- This may result in personal injury and shorten the product life.

ࣃ

If it seems that grounding is needed due to water or moisture, make sure to run grounding wires.

- Failure to do so may result in electric shock due to electric leakage.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды