Samsung DW80M9* Series Скачать руководство пользователя

Страница: 46 / 62

44 _ Troubleshooting

Item

Related

Parts

Symptoms

Description

n5: Setting Dry

Increase Option by

Default

1) If Dry+ (or Sanitize) option is set to On by default, it indicates as "d1”.

2) If Dry+ (or Sanitize) option is not set to On by default, it indicates as "d0“.
1. To set Dry+ (Sanitize) option to On by default, use the Dry+ (Sanitize) option button to switch it On/Off [n5: Setting Dry Increase

Option by Default mode only].

- When Dry+ (Sanitize) button is pressed, Dry+ (Sanitize) is set to On or Off by default.

※

For models without Dry+, the Sanitize button can be used to set the Sanitize option to On by default.

About This Option

This option is designed to increase the drying performance by default in case there are consumer complaints.

- If Dry+ (Sanitize) option can be set to On by default, it powers on and sets the Dry+ (Sanitize) option to On by default.

- If the course does not support Dry+ (Sanitize) option setting, it is not set to On by default.

- Even if the course is completed without using Dry+ (Sanitize) option, the last used course is set to On by the course save feature

on its next power-on and Dry+ (Sanitize) option is set automatically depending on the default setting as long as Dry+ (Sanitize)

option is set to On by default.

- Even if Dry+ (Sanitize) option is automatically set by the default setting, it can be switched on/off by pressing Dry+ (Sanitize) Key.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды