Samsung DW80M9* Series Скачать руководство пользователя

Страница: 14 / 62

12 _ Disassembly and Reassembly

Part

Figure

Description

Door outer

Preparation:

• Make sure to disconnect the power.

• Remove the lower basket in the dishwasher.

• Cover the Assy sump with a towel to prevent

losing screws.

1. Open the door completely to prevent losing

screws.

Before removing the parts, place a cushioned

mat on the floor to prevent the parts from being

scratched.

2. Remove the 12 screws (short one 8 pieces, long

one 4 pieces) which holding the door outer and

control panel in place.

After removing screws, make sure to hold the door

outer using your hand. This will prevent the door

from closing suddenly and harming you.

Caution

Do not place the removed screws on the door

inner. They may fall into the sump assy.

3. Pull out the door outer carefully.

4. Separate wire connectors indicated by the red

arrows in the picture to the left and separate the

Wire from the Hook shown with red arrow.

- DW80M9960US/UG : 10 wire connectors

- DW80M9550US/UG : 8 wire connectors

5. Lay a mat on the floor to protect the Door and put

down the Assy door outer.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды