Samsung DW80M9* Series Скачать руководство пользователя

Страница: 53 / 62

Troubleshooting_51

Check type

Check code

Checking method

Corrective actions

No Power check

None

1. Check the connections for the power plug.

- Reconnect the power plug.

2. Check the voltage of the power outlet.

► Normal : 120V

- Connect to a 120V power source.

3. Check Power Key on state.

- Try to touch the Power key.

4. Check the connections for the Sub PBA and Touch PBA connector parts.

- Reconnect the Sub PBA and Touch PBA connectors.

5. Check the connection of the Main PBA connector CN101

- Reconnect CN101

6. Check the connections for the Sub PBA and Main PBA connector parts.

- Reconnect the Sub PBA and Main PBA connectors.

7. Check whether there is condensation on the PBA.

- CN103 of Display Control Module connector.

- CN100 TOUCH Module connector.

► Normal: No condensation

- Faulty: Remove any condensation and moisture.

- Normal: Replace the Control Panel Assy.

8. Check the DC voltage of the Main PBA.

- See “Main PBA DC voltage check code”.

9. In case of is No Power after Method 1~10 action

- Replace the Control Panel Assy.

(Sub, Touch, wire)

10. In case of is No Power after Method 1~11 action

- Replace the Main PBA.

Display check

None

1. Check the connections for the Display LED connector part.

- Reconnect the connectors for Display LED.

2. Check the Display LED.

- Faulty: Replace the Display LED and Sub PBA.

Dry check

None

1. Check the wire connections for the Fan Motor.

- Reconnect the Fan Motor connectors.

2. Check the resistance of the Fan Motor coil.

(Remove the connector before measuring.)

► Normal: Approx. 150Ω

- Faulty: Replace the Fan Motor Assy.

3. Check the resistance of the Thermal Actuator.

(Remove the connector before measuring.)

► Normal: Approx. 1.45kΩ

- Faulty: Replace the Thermal Actuator.

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды