Samsung DW80M9* Series страница 47 Скачать руководство пользователя

Страница: 47 / 62

Troubleshooting_45

Check type

Check code

Checking method

Corrective actions

Water supply

check

1. Check whether the faucet is open.

- Open the faucet.

2. Check whether the water supply has been cut off.

- After wait until the water supply resumes and turn off the power.
- After the water supply resumes, turn on the power.

3. Check whether any foreign material is in the Water Supply Line and the

Water Valve filter.

- Remove the foreign material, clean the filter in Water Valve with a brush.

4. Check the connection for the Water Valve connector.

- Reconnect the Water Valve connector.

5. Check whether the coil in Water Valve is conductive.

(Remove the connector before measuring.)

► Normal: Approx. 990Ω ± 10% (890Ω~1089Ω)

- Faulty: Replace the Water Valve.

6. Check whether the water supply stops, after water is supplied for 20

seconds.

- Faulty: Replace the Water Valve and Assy guide water-sub.

7. Check whether the water supply stops after water is supplied for

60minutes.

- Check the water supply pressure. (> 0.5bar)
- Faulty: Replace the Water Valve and Assy guide water-sub.

8. Check whether the Water Valve is operating normally in the Main PBA.

- Check the Water Valve Relay in Main PBA.
: Check the voltage between the Blue wire (Number6) of the CN401 and

the White wire of the CN101 connector.

► Normal: 110 ~120V (while operating)

- Faulty: Replace the Main PBA Assy.
- Normal: Replace the Water Valve.

9. Check the Power Relay.

- See the “Power Relay check code”.

4-3. CHECK CODE TROUBLE SHOOTING

Содержание DW80M9* Series































































Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды

Samsung DW80M9* Series, Руководство по обслуживанию

Результаты поиска

Содержание DW80M9* Series

Отзывы:

Похожие инструкции для DW80M9* Series

Бренды по названию

Популярные бренды