Sakai CR271 Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 170

background image

6-001

DRUMS

1. PRECAUTIONS FOR DISASSEMBLY AND REASSEMBLY

• When removing, installing, disassembling or reassembling the unit, observe the general

precautions described below.

1) Precautions for removal work

• Coolant that contains antifreeze should be treated as a chemical, and must not be drained

carelessly on the ground.

• To prevent dust from getting into disconnected hoses and tubes, cover them with a plug or similar

means.

• When draining oil, use a receptacle with sufficient capacity to receive it.
• Before proceeding with the work, look for matchmarks that show the installation location. For

reassembly, place matchmarks in the required locations to prevent errors. Then remove.

• When disconnecting wiring connectors, hold the connector components so that unreasonable force

is not applied to the wires.

•  Label wires and hoses to ensure correct installation location.
•  Confirm the number and thickness of shims prior to storage.
•  When lifting parts, use lifting equipment of sufficient capacity.
•  When separating parts by using pull bolts, tighten the bolts alternately.
•  Before removing a unit, clean its surrounding area. Then after removal, cover it to prevent dust

and other substances from getting in.

• Before removing piping for hydraulic oil or coolant, or removing related parts, satisfactorily release

internal pressure.

2) Precautions for installation work

•  Tighten bolts and nuts (sleeve nuts) to the specified torque (screw tightening torque table).
•  When installing hoses, do not twist them or allow them to interfere with other parts.
•  Replace gaskets, O-rings, split cotter pins, and lock plates with new parts.
•  Properly bend split cotter pins and lock plates.
•  When applying an adhesive, first clean and remove oil/grease from the surfaces properly. Then

apply two or three drops to the threaded areas.

• When applying a liquid gasket, first clean and remove oil/grease from the application surface

properly, and confirm that the surface is free of dust and damage. Then apply the product evenly.

•  Clean parts well. Repair scratches, dents, burrs, rust, etc.
•  Apply gear oil to rotating and sliding components.
•  Apply grease to the surfaces of press-fit parts.
•  After installing snap rings, confirm that they are properly seated in the grooves.
•  Connect wiring connectors securely after cleaning off adhering oil, dust and water.
•  Use lifting bolts that are not fatigued or deformed. Screw them in fully.
•  When tightening a split flange, tighten screws alternately to prevent uneven tightening.
•  Before installing hydraulic parts, confirm that they are free of damage and dust, etc.

«
...
71
72
73
74
75
...
»

Содержание CR271











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CR271

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: FENDT Страницы: 31

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

Бренд: Badger Meter Страницы: 16

Бренд: CAE Healthcare Страницы: 108

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: Jaga Страницы: 32

Бренд: xsto Страницы: 63

Бренд: Megger Страницы: 12

Бренд: Tecsis Страницы: 52

LIGHTHOUSE SPORT 3.18

Бренд: Raymarine Страницы: 162

CarePump Lite 6

Бренд: BARDOMED Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды