Sakai CR271 Скачать руководство пользователя страница 147

Страница: 147 / 170

10-005

TROUBLESHOOTING

1-2) Measuring resistance of harness (measuring resistance between terminal 1 of equipment A and terminal 2

of equipment B)

GW750-2-10005

Equipment A

Connector A

Harness

Ohmmeter

(tester)

Main power source

of equipment B

Ground of

equipment A

Signal from

equipment A

Power to

equipment A

Connector B

Equipment B

Equipment A

Equipment B

Inspection procedure

①

Disconnect the connectors of equipment A and equipment B.

②

Connect the test probe (+) to connector terminal 1 of equipment A and the test probe (-) to connector

terminal 2 of equipment B and measure the resistance. At this time, reversing the connector terminals

between the probes (+) and (-) does not make any difference in the measurement.

Criteria for harness defects

When there is no abnormality in the harness: Less than 10 Ω (measured value)

If there is any abnormality in the harness such as broken wire: 10 Ω or higher (measured value)

1-3) Measuring resistance of grounding wire (measuring resistance between terminal 5 of equipment B and

ground)

GW750-2-10006

Connector A Harness

Ohmmeter

(tester)

Main power source

of equipment B

Equipment B

Battery

Equipment B

Inspection procedure

①

Disconnect the connector of equipment B.

②

Connect the test probe (+) to connector terminal 5 of equipment B and the test probe (-) to a machine

ground point (the bolt fastening the ground terminal or an unpainted portion on the body) and measure

the resistance. At this time, reversing the connector terminals between the probes (+) and (-) does not

make any difference in the measurement.

(NOTICE)

•

When measuring the resistance, connect the test probes to both ends of the portion to be

measured. Make also sure that no voltage is applied to the portion to be measured.

• When measuring the internal resistance of equipment, be sure first to disconnect all harnesses

from the equipment.

•

When measuring the resistance of a harness, disconnect the equipment connected to both ends

of the harness.

Содержание CR271











































































































































































Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды

Sakai CR271, Руководство по ремонту

Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды