Sakai CR271 Скачать руководство пользователя страница 136

Страница: 136 / 170

9-010

INSPECTION AND ADJUSTMENT

7. ADJUSTMENT OF THROTTLE LEVER LINKAGE

7-1. Adjustment

• In cases such as maximum no-load rotational speed or

minimum no-load rotational speed deviating from standard
value, control cable is replaced, or throttle lever does not
move smoothly, make an adjustment in accordance with
procedure described below.

• Make the adjustment after amply warming up engine.
• Oil temperature during measurement : 50

± 5

°C (122

± 9

°F)

①

Set throttle lever (1) to “IDlE”.

②

Attach control cable (2) to throttle lever (1).

③

Attach control cable (2) to control lever (5) of control

ASSY on the engine side.

④

Start the engine.

⑤

loosen lock nut (3).

⑥

Using stopper bolt (IDlE) (4), adjust so that standard

minimum no-load rotational speed is achieved.

★

Standard minimum no-load rotational speed

: 1,400

± 150

rpm

⑦

Using lock nut (3), firmly secure stopper bolt (4).

CR271-09010

IDLE

CR271-09011

Содержание CR271











































































































































































Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды

Sakai CR271, Руководство по ремонту

Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды