Sakai CR271 Скачать руководство пользователя страница 157 | Manualshive

Страница: 157 / 170

background image

10-014

TROUBLESHOOTING

2-2-2. Engine will not start (But starter motor runs)

•

In case of engine will not start while starter motor runs, generally trouble is caused by that fuel is not
supplied, supply amount of fuel is extremely low, or selection of fuel is not appropriate.

•

Check that fuel is supplied to inlet of fuel pump.

Reference Fig.: 2-2-1

Check point

Check/Cause

Action

1. Fuel Pump

•

When starter switch is ON, measure voltage between fuel

pump terminal wire R and chassis ground.

Standard voltage : 12 V or more

•

If voltage is OK and engine will not start, fuel pump is

faulty.

Replace fuel pump.

2. Fuel Cut Solenoid

•

When starter switch is ON, measure voltage between fuel

cut solenoid terminal wire marked

FUL CUT

and chassis

ground.

Standard voltage : 12 V or more

•

If voltage is OK and engine will not start, fuel cut solenoid

is faulty.

Replace fuel cut

solenoid.

3. Engine Stop Relay

(1) When starter switch is ON, measure voltage between

engine stop relay terminal b and chassis ground.

Standard voltage : 12 V or more

(2) When starter switch is ON, check continuity between

engine stop relay terminal c and terminal e.

There is continuity in normal condition.

•

If above item (1) is OK and item (2) is NG, engine stop

relay is faulty.

Replace engine stop

relay.

4. Harness Connecting

Between Terminals

•

Measure resistance of harness connecting between

terminals.

Standard resistance : 10 Ω or less

•

If resistance is abnormal, harness is faulty.

Repair or replace

harness.

«
...
155
156
157
158
159
...
»

Содержание CR271











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CR271

Бренд: Panasonic Страницы: 9

Бренд: National Instruments Страницы: 16

Бренд: Jasco Страницы: 11

Бренд: Panasonic Страницы: 180

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: Pari Страницы: 50

Бренд: Icare Страницы: 42

IP Video Test Option HST-3000

Бренд: JDS Uniphase Страницы: 4

Бренд: Jct Страницы: 16

Бренд: Rane Страницы: 6

Бренд: Rane Страницы: 27

Бренд: Ranger Products Страницы: 6

Бренд: Rane Страницы: 88

Бренд: Haag-Streit Страницы: 21

APT-9411 Series

Бренд: TAKAYA Страницы: 77

Бренд: Tadano Страницы: 402

Бренд: Ultimate Healthcare Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды