Sakai CR271 Скачать руководство пользователя страница 128

Страница: 128 / 170

9-002

INSPECTION AND ADJUSTMENT

2. MEASUREMENT AND INSPECTION OF PROPULSION

CIRCUIT PRESSURE

2-1. Measurement

WARNING

Confirm that the parking brake works properly before

measurement.

• Oil temperature during measurement : 50

± 5

°C (122

± 9

°F)

①

Remove plugs from high pressure gauge port (1-2) and
(1-1) of propulsion pump. Attach pressure gauge with
adapter

ⓨ

• Adapter

: 7/16-20UNF

•  High pressure gauge port (Reverse) : (1-2)
•  High pressure gauge port (Forward) : (1-1)
•  Pressure gauge

: 0 to 25 MPa

(0 to 3,625 psi)

②

Start the engine and set throttle lever to “FUll”.

③

Establish a condition in which machine propulsion load
becomes maximum.

(Pressure does not build up unless propulsion load is
applied.)

④

With propulsion load at maximum, slowly move F-R lever
to the side to be measured.

• Then, read pressure indicated by pressure gauge.

⑤

After measuring, promptly return F-R lever to “N”.

★

Maximum circuit pressure
(high pressure relief valve setting)

: 17.2

± 1.0

MPa (2,494

± 145

psi)

• The number “1-1” and “1-2” appearing in above illustrations are consistent with lead line number shown in

illustration of propulsion pump in “2-2. Hydraulic Component Specifications” (page 4-006).

CR271-09001

1-1

1-2

PG001011

Содержание CR271











































































































































































Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды

Sakai CR271, Руководство по ремонту

Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды