Sakai CR271 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 170

background image

10-010

TROUBLESHOOTING

3) Connector inspection

•

Is a connector disconnected or loose?

•

Check that pins are not snapped or corroded.

•

If faulty contact is suspected
Turn the starter switch OFF. Then disconnect and check the connectors (including relay and switch
sockets).
If the terminal has no luster, faulty contact due to oxidation can be suspected. Therefore, polish the terminal

by inserting and removing the connector (relay, switch) repeatedly at least five times. (Luster will return.)

4) Relay inspection (Check ON/OFF operation by sound.)

•

Conduct without running the engine. (If you run the engine, you cannot hear the sound of operation.)

Sound heard

: A relay failure occurred.

No sound heard : Using a tester, check the harness.

Sound heard : A relay failure occurred.

Still no sound : Using a tester, check the harness.

Continuity :

Turn the starter switch OFF temporarily, disconnect the relay and check
for continuity between the harness-side grounding terminal (color: black)
and vehicle body ground. (If there is none, replace the harness.)

Voltage

: With the relay disconnected, turn the starter switch ON and turn the

operating switch ON. 24 V (or 12 V) (between vehicle body ground) should

not reach the relay coil input terminal. Confirm this. Identify the location

(section) to which 24 V (or 12 V) reaches. Then replace the harness or
take other action.

5) Solenoid valve inspection (Check ON/OFF operation by sound.)

•

Conduct without running the engine. (If you run the engine, you cannot hear the sound of operation.)
Sound heard

: The electrical system is normal.

No sound heard : Check with a tester.

Continuity :

①

Turn the starter switch OFF temporarily, disconnect the connector and
check for continuity between the harness-side grounding terminal (color:
black) and vehicle body ground. (If there is none, replace the harness.)

:

②

Is the solenoid valve coil burnt?
(Turn the starter switch OFF, disconnect the connector and check the
resistance between the solenoid valve terminals.)

Voltage : With the connector disconnected, turn the starter switch ON and check

whether 24 V (or 12 V) exists between the harness-side connector and
vehicle body ground.

If YES : Replace the valve.

If NO : Investigate and identify the location (section) to which 24 V (or 12 V)

reaches. Then replace the harness or take other action.

6) Harness check

•

If an incomplete disconnection inside the harness is suspected, wiggle (move) the harness during the relay
inspection and solenoid valve inspection to see whether the relay (valve) operates incorrectly.

•

Check for burned areas of the harness.

•

Turn the starter switch OFF, disconnect the connector and check the continuity, referring to the circuit
diagram and wiring coloring.

«
...
150
151
152
153
154
...
»

Содержание CR271











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CR271

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Crouse-hinds series

Бренд: Eaton Страницы: 32

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

AirForm Night Splint

Бренд: Össur Страницы: 16

Бренд: Össur Страницы: 17

Бренд: Warner Electric Страницы: 14

Бренд: FoodMarble Страницы: 44

Бренд: ISA Страницы: 24

Бренд: Torque Страницы: 10

Portable Vocal Booth Pro Studio Series

Бренд: EditorsKeys Страницы: 2

Calculite C6P38MHA

Бренд: Lightolier Страницы: 2

Бренд: König Electronic Страницы: 100

Бренд: probst Страницы: 112

Бренд: TECSYSTEM Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды