Sakai CR271 Скачать руководство пользователя страница 133

Страница: 133 / 170

9-007

INSPECTION AND ADJUSTMENT

4-2. Adjustment

• If measurement results indicate the pressure deviating

from standard maximum circuit pressure range, make an
adjustment in accordance with procedure described below.

①

Check relief valve (2) for evidence of having loosened.

②

If there is evidence of relief valve having loosened, adjust
it so that pressure becomes within standard maximum
circuit pressure range while watching pressure gauge.

• To adjust pressure, loosen adjustment plug (3).

Adjustment plug turned clockwise

: Pressure rise

Adjustment plug turned counterclockwise

: Pressure drop

Pressure change rate : 1.8 MPa/turn (261 psi/turn)

③

If there is no evidence of having loosened, remove relief
valve.

④

Check removed relief valve for trapped dirt and scratches
on its seat.

⑤

If trapped dirt is present, disassemble and clean relief
valve.

⑥

If a scratch is found on seat, replace relief valve.

⑦

After adjustment, measure pressure again and check that
pressure reaches standard maximum circuit pressure
range.

(NOTICE)

•

Carefully disassemble and reassemble after taking
steps to prevent foreign material from getting in.

CR271-09006

CR271-09007

Содержание CR271











































































































































































Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды

Sakai CR271, Руководство по ремонту

Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды