Sakai CR271 Скачать руководство пользователя страница 83

Страница: 83 / 170

6-011

DRUMS

4. DISASSEMBLY AND REASSEMBLY OF DRUMS

4-1. Disassembly of Drums

• Lead line numbers shown in the illustrations for the following drum disassembly and reassembly

procedures are constant with part numbers of drum assembly shown on page 6-008, 6-009.

4-1-1. Front drum

1) Remove nuts (14), (32).

• Remove bracket (15), (31).

(15), (31) Bracket : 25 kg (55 lbs.)

CR271-06012

•

When standing the vibratory drum, use

wooden blocks of sufficient strength to

securely support the drum.

•

Carry out the work in an unstrained posture

using a work stool or the like.

2) Stand vibratory drum ASSY with its vibrator motor

(28) side facing up.

Vibratory drum ASSY : 330 kg (728 lbs.)

CR271-06013

Vibratory drum

ASSY

3) Remove bolts (27).

• Remove vibrator motor (28).

(28) Vibrator motor : 3 kg (7 lbs.)

CR271-06014

Содержание CR271











































































































































































Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды

Sakai CR271, Руководство по ремонту

Результаты поиска

Содержание CR271

Отзывы:

Похожие инструкции для CR271

Бренды по названию

Популярные бренды