Sakai CR271 Скачать руководство пользователя страница 143 | Manualshive

Страница: 143 / 170

background image

10-001

TROUBLESHOOTING

1. TROUBLESHOOTING

1-1. Safety Precautions for Troubleshooting

WARNING

Unexpected machine movement may cause a serious accident. When inspecting the machine while the
engine is running, always follow the instructions below.

• Park the machine on level, flat ground.
•

Apply the parking brake.

•

Set chocks in front and behind each drum or tire.

•

Make sure that service personnel are given the appropriate information at the appropriate time.

•

Make sure that no one can enter any hazardous area.

CAUTION

Do not work on the hydraulic system while the engine is running and the system is hot and under pressure.

Do not disconnect hydraulic hoses or fittings until the system has cooled and pressure has been properly

relieved.
Before removing any plugs from the pressure measurement ports, always release any residual pressure

from the piping and open the cap of the fluid tank to release and pressure.

WARNING

Inadvertent starting the engine may cause a serious accident.
When inspecting the engine, make sure to exchange the appropriate cues and hand signal with the person
at the operator station to avoid any accidents.

CAUTION

Before inspecting inside of the engine compartment, always stop the engine.
Contact with the fan, V-belt or exhaust system parts while the engine is running may cause serious injury.

1-2. Important Information for Troubleshooting

Before conducting troubleshooting, it is important to carefully read the operation manual and workshop manual
and understand the electric circuits for each component as well as the structure and function of each system.

Sufficient knowledge of the systems will enable you to identify a possible cause much faster. A fault or problem

may seem to be related to many different factors. To identify the true cause, some experience is needed. To
perform the appropriate troubleshooting, it is important to learn not only the normal operations of the systems but
also the possible symptoms that may occur when an abnormal condition is present.
This chapter explains the possible causes and remedies for likely incidents taken from past experience.

«
...
141
142
143
144
145
...
»

Содержание CR271











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CR271

Бренд: Canta Страницы: 2

Movie FL Black E27 Flaps

Бренд: Qazqa Страницы: 2

Бренд: MAGIC FX Страницы: 25

Бренд: Pari Страницы: 11

Бренд: Pari Страницы: 2

Бренд: Haas Страницы: 5

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 24

Бренд: H&S Страницы: 32

Бренд: Olympus Страницы: 130

Бренд: Vibration Research Corporation Страницы: 333

CHIEFTAIN E1006

Бренд: Falcon Страницы: 5

Бренд: Feniex Страницы: 5

Бренд: Analogue Solutions Страницы: 64

Power System KPS-US

Бренд: Keys Fitness Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды