RuiDa RDC6563F Скачать руководство пользователя страница 38

Страница: 38 / 107

RDC6563F Standalone Fiber Cutting Control System User Manual V2.0

SHENZHEN RUIDA TECHNOLOGY CO., LTD

2.16 Indicator Description

Type

Definition

Description

X AXIS

LMT+

X-axis positive limit indicator

When the input port is low voltage,
the indicator is on.

LMT-

X-axis negative limit indicator

When the input port is low voltage,
the indicator is on.

ALM

X-axis servo drive alarm
indicator

When the input port is low voltage,
the indicator is on.

SON

X-axis servo drive enable
indicator

When the input port is low voltage,
the indicator is on.

+5V

+5V Power Indicator

When the system power is normal,
the indicator is on.

ERR

System error indicator

When the mainboard hardware
fails, the indicator light is on.

RUN

System operation indicator

When the system is running
normally, the indicator light flashes
at a frequency of 2 seconds/time.

Y1/Y2 AXIS

LMT1+

Y1 axis positive limit indicator

When the input port is low voltage,
the indicator is on.

LMT1-

axis

negative

limit

indicator

When the input port is low voltage,
the indicator is on.

ALM1

Y1 axis servo drive alarm
indicator

When the input port is low voltage,
the indicator is on.

SON1

Y1 axis servo drive enable
indicator

When the input port is low voltage,
the indicator is on.

LMT2+

Y2 axis positive limit indicator

When the input port is low voltage,
the indicator is on.

LMT2-

axis

negative

limit

indicator

When the input port is low voltage,
the indicator is on.

ALM2

Y2 axis servo drive alarm
indicator

When the input port is low voltage,
the indicator is on.

SON2

Y2 axis servo drive enable
indicator

When the input port is low voltage,
the indicator is on.

U/A AXIS

U-LMT+

U-axis positive limit indicator

When the input port is low voltage,
the indicator is on.

U-LMT-

U-axis negative limit indicator When the input port is low voltage,

Содержание RDC6563F












































































































Результаты поиска

Содержание RDC6563F

Отзывы:

Бренды по названию

Популярные бренды

RuiDa RDC6563F, Руководство пользователя

Результаты поиска

Содержание RDC6563F

Отзывы:

Бренды по названию

Популярные бренды