125
Troubleshooting
Problem
Items to check
Action
Page
Sound is still heard from the
opposite side as well even
when panned all the way to
one side
Could effects be applied?
Since the FANTOM’s internal effects are stereo, applying an insert effect
will allow effect sound to be heard from the opposite side even if the
source sound is panned all the way to one side .
–
Notes played in a high
register sound funny
When you play high notes on the FANTOM, you might
hear notes that fail to sound, whose pitch fails to rise, or
a noise that changes depending on the note you play (a
warbling, chirping, rustling, beeping, etc .)
This is usually because you have exceeded the highest note that the
FANTOM is able to produce, and won’t occur with the notes you would
normally use . This does not indicate a malfunction .
–
Can’t play arpeggios
Could the zone’s ARP Switch be “OFF”?
Turn the applicable zone’s ARP Switch “ON .”
Even if the [ARPEGGIO] button is on, an arpeggio will not play unless
the zone’s ARP Switch is “ON .”
Can’t perform using the
chord memory function
Could the zone’s ARP Switch be “OFF”?
Turn the applicable zone’s ARP Switch “ON .”
Even if the [CHORD MEMORY] button is on, you can’t use chord
memory performance unless the zone’s ARP Switch is “ON .”
Pitch sometimes fails to rise
when playing legato
When the Legato Switch is “ON” and Legato Retrigger
is “OFF,” and you hold down a low note and play a high
note to produce a legato effect, the pitch might stop at a
certain point and fail to rise as far as you expect because
the upper limit of the wave data has been exceeded . If the
tone uses multiple waves, and each of these waves has
a different upper limit, the result might no longer sound
mono .
If you want to make large changes in the pitch, you should turn Legato
Retrigger “ON .”
For details on the parameters, refer to “Parameter Guide” (PDF) .
–
When you press a sample
pad or note pad, the sound
remains “stuck” on
Could the [HOLD] button be lit?
Press the [HOLD] button once again to make the button go dark .
–
Sound does not stop when
you press a sample pad.
Could the sample parameters GATE SW and LOOP SW
both be off?
When the sample parameters GATE SW and LOOP SW are both off,
one-shot playback occurs, meaning that once the sample is triggered
by the pad, it continues to play to the end of the waveform .
For this reason, when playing a long sample, it may seem that the
sound cannot be stopped .
In such situations, press the [HOLD] button four times in rapid
succession . This stops all sounds that are being played by the pads .
Problems with the effects
Effect not applied
Could the effect switch be off?
Check the on/off setting of each effect .
Check the send level to each effect .
The effect won’t be obtained if the send level to that effect is set at 0 .
Even if the send levels to the effect is set above 0, the effect won’t be
applied if the multi-effect level, or reverb level are set to 0 . Check each
of these settings .
You specified a delay time
value (for example for
multi-effect DELAY) as a
note value, but there’s a
limit beyond which the
delay time will not change
Check the delay time setting .
Since the delay time has an upper limit, specifying the delay time
as a note value and then slowing down the tempo may reach this
upper limit . The maximum delay time is the highest value that can be
specified numerically (i .e ., other than in terms of a note value) .
For details on the parameters, refer to “Parameter Guide” (PDF) .
–
The Modulation or other
controller is always on
Check the matrix control settings .
For Z-Core tones, you can use matrix control to control the tone in real
time . Matrix control uses MIDI messages such as incoming MIDI control
changes as a source to modify the parameters of a tone .
Depending on these settings, the FANTOM may respond to MIDI
messages from an external MIDI device and be in an unexpected state .
For details on the parameters, refer to “Parameter Guide” (PDF) .
–
Problems with the sequencer
After recording, there’s no
sound when you play back
the pattern
Could a specific track be muted?
Defeat muting .
Could a specific track be soloed?
Defeat solo .
The tempo is different
than when the pattern was
played a previous time
Did you save the scene?
When you change the tempo and play back, the FANTOM does not
save that tempo unless you save the scene . If you want to keep the
modified tempo, save the scene .
After playing a song on
the sequencer, there is no
longer sound
Could the song data contain data that set the volume to
zero?
After playing a song that ends with a fade-out, sound might no longer
be heard . In this case it may be that a volume message or expression
message has lowered the volume . Check each value and set it
appropriately .
–
Содержание FANTOM Series
