Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 7

Страница: 7 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Preface

Introduction

This user manual provides installation instructions and maintenance

procedures for the Rockwell Automation Bulletin 7712 ArcShield™ arc flash

resistant enclosure, medium voltage controller. The Bulletin 7712 structure

provides one complete MV controller unit.

Summary of Changes

This manual contains new and updated information as indicated in the

following table.

Who Should Use this Manual

This manual is intended for qualified service personnel responsible for

installing and maintaining medium voltage controllers. You should have

previous experience with, and an understanding of, electrical terminology,

procedures, required troubleshooting equipment, equipment protection

procedures and methods, and safety precautions. See safety related practices

contained in publication NFPA 70E, Standard for Electrical Safety in the

Work Place.

Service and Maintenance

For your convenience, Rockwell Automation Customer Support and

Maintenance (CSM), provides an efficient and convenient method of servicing

medium voltage products. Contact your local area support office to make

arrangements to have a qualified service representative come to your facility. A

complete listing of Area Support Offices may be obtained by calling your local

Rockwell Automation Distributor or Sales Office.

For Medium Voltage technical support on start-up or existing installations,

contact your Rockwell Automation representative. You can also call 1-519-

740-4790 for assistance Monday through Friday from 9:00 a.m. to 5:00 p.m.

(Eastern Time zone).

ArcShield Arc Flash Resistant

Enclosure Features

Built to minimize exposure to electrical hazards, the OneGear 7.2 kV motor

controller includes an optional earthing switch and fully interlocked

compartment doors to isolate the power source when an apparatus cell door is

open. The controller features ArcShield arc flash-resistant enclosures, which

provide arc-flash protection in accordance with the IEC 62271-200 Annex A

standard.

The controller is designed, manufactured and tested to meet or exceed the

applicable requirements of the latest standards published by the following

organizations:

• IEC 60470: High-voltage Alternating Current Contactors and

Contactor Based Motor-Starters.

Topic

Page

Replaced Spare Parts List

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды