Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 63

Страница: 63 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Appendix

Troubleshooting

Door Interlock Circumvention

Door interlocks ensure user safety and should only be defeated in the event of

mechanical failure.

Earthing Switch to Door

1. Open the LV door.
2. In order to circumvent the earthing switch to door interlock, remove

three M6 flat head screws located on the door (

Figure 43

ATTENTION:

This procedure requires contact with medium voltage

components. To avoid shock hazards, complete the Power Lockout procedure
on

page 27

before servicing the equipment. Verify with a hot stick or

appropriate voltage measuring device that all circuits are voltage free. Failure
to do so may result in severe burns, injury or death.

WARNING:

Use suitable personal protective equipment (PPE) per local codes

or regulations. Failure to do so my result in severe burns, injury, or death.

IMPORTANT

Before circumventing earthing switch to door interlock:
• The contactor cart must be in the test/withdrawn position.
• This procedure should only be used if the earthing switch cannot be

closed causing the door not to open.

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды