Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 22

Страница: 22 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Chapter 3

Start-up Procedure

When the contactor cart is racked to operating position, the MV parts on the

line side, including CPT is default has been chosen, would be connected to the

line side buses of this equipment so that they would be energized by MV. As a

result of energizing CPT, control power would be applied to the LV circuit

connected to it.

The cart must be in the operating position and the earthing switch must be

open.

It is not possible to operate the contactor by the test power supply while the

contactor cart is in operating position. To perform any operation with the

contactor engaged, either MV should be applied on the line side bus of this

equipment so that the MV energized on-cart CPT would power up the control

circuits, or a customer supplied power supply should have been wired to the LV

panel as designed.

Test the Contactor

Contactor must be in the withdrawn/test position

1. Connect the appropriate external power supply (120V or 230V AC) to

the test receptacle in the control panel. Turn the selector switch to the

TEST position.

2. Electrically operate the contactor several times. Inspect the armature

plate to verify that it fully contacts the magnetic cores.
Contactor should close when close command is given. IntelliVAC

module will detect and display fault if a problem exists.

3. Turn the selector switch to the OFF position and disconnect the

external power supply.

Inspect the area around the magnetic cores of the vacuum contactor and

remove any metal filings, if present. This type of debris is attracted to the coil

once it is energized and could prevent the contactor from closing properly.

ATTENTION:

Some control circuit configurations may require control jumpers

to let the contactor close during the test procedure. Do not jumper any

contactor cart position auxiliary contacts. Using jumpers for these contacts
can result in equipment damage or injury to personnel.

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды