Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 39

Страница: 39 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Maintenance

Chapter 5

Coils

If a coil exhibits evidence of overheating (cracked, melted or burned

insulation), it must be replaced. In that event, check for and correct overvoltage

or undervoltage conditions, which can cause coil failure. Be sure to dean any

residues of melted coil insulation from other parts of the device or replace such

parts.

Pilot Lights

Replace any burned out lamps or damaged lenses. Photoelectric Switches-The

lenses of photoelectric switches require periodic cleaning with a soft dry cloth.

Reflective devices used in conjunction with photoelectric switches also require

periodic cleaning. Do not use solvents or cleaning agents on the lenses or

reflectors. Replace any damaged lenses and reflectors.

Annual Maintenance

Requirements

Task

Page

Remove Contactor Cart

Remove and Replace Fuses

Contactor Cart Maintenance

Replace the Vacuum Bottles

Calibrate the Overtravel and Contact Gap

Lubricate the Contactor Cart

Earthing Switch Maintenance

Inspect and Lubricate Earthing Switch Mechanism

Ground Connection Inspection

Toggle Assembly Inspection

Earthing Switch Auxiliary Maintenance

Auxiliary Contacts Replacement

Auxiliary Contacts Adjustment

Earthing Switch Auxiliary Contacts Inspection

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Бренды по названию

Популярные бренды