Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 20

Страница: 20 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

Chapter 3

Start-up Procedure

Testing Contactor Operation

The contactor must be tested without any applied medium voltage. This

should be done for initial startup and after any maintenance is performed. This

test power supply should be within the IntelliVAC™ Vacuum Contactor

Controller specifications (

1503-UM053

). CPT on the cart is not energized

when the contactor is in the test/withdrawn position.

Connect an appropriate power cord to the power receptacle in the low voltage

compartment (

Figure 5

Figure 5 - Location of Control Switch and Auxiliary Power Receptacle

It is possible to open the MV door while the cart is in the test/withdrawn

position and the earthing switch is closed. The shutter behind the cart in the

MV compartment should be closed under this situation. This should be

confirmed after opening the MV door.

If the MV door cannot be opened smoothly, the shutter is not completely shut

off or the earthing switch is not completely closed.

ATTENTION:

Always perform the power lockout procedure before servicing

equipment. Failure to do so may result in severe burns, injury or death.

ATTENTION:

The following procedure requires racking the contactor cart to

its test position. To avoid potential of shock hazards, disconnect and lockout

incoming power before proceeding. Failure to lockout incoming power will
result in a live bus cell. Once the shutter between power cell and bus cell is
open, it may cause severe burns, injury or death. Rockwell Automation does

not assume any responsibility for injuries to personnel who have not
completed the following safety procedure prior to servicing the equipment.

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Похожие инструкции для Allen-Bradley 7712

Бренды по названию

Популярные бренды