Rockwell Automation Allen-Bradley 7712 Скачать руководство пользователя страница 13

Страница: 13 / 74

Rockwell Automation Publication 7712-UM001D-EN-P - October 2017

General Information

Chapter 1

ArcShield Components

Installation Requirements

The Bulletin 7712 ArcShield enclosure typically includes a pressure relief vent.

The pressure relief vent opens under arc flash conditions, allowing hazardous

flames and gases to exit the enclosure via plenum.

ATTENTION:

The low voltage panel area is sealed to prevent flames and

gases from entering; however, suitable personal protective equipment (PPE)
must be used whenever working on live circuits.

ATTENTION:

To ensure arc flash resistant integrity:

• The pressure relief vent must not be tampered with and must not be used as

a step.

• No alterations can be made to the ArcShield structure.
• All covers, plates, and hardware removed for installation or maintenance

purposes must be re-installed and properly secured. Failure to do so voids

the arc flash resistant integrity.

• Power cable entry points are to be treated as the boundary between a

hazardous location and sealed accordingly. Failure to do so voids the arc flash

resistant integrity.

• A plenum must be used to direct the arc flash energy to a suitable location.

Failure to do so voids the arc flash resistant integrity. See Publication

7712-

IN001

for plenum installation instructions.

• All wiring between the low voltage panel and the power cell must be routed

through a suitable gland to ensure flames and gases are not transmitted into
this area (as fitted from factory).

• The medium voltage power cell doors must be properly secured, using the

handle mechanism (refer to instruction label on the power cell door and

page 16

). Failure to do so voids the arc flash resistance integrity.

Содержание Allen-Bradley 7712











































































Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley 7712, Руководство пользователя

Результаты поиска

Содержание Allen-Bradley 7712

Отзывы:

Бренды по названию

Популярные бренды