manualshive.com logo in svg

Rockford Systems Stop-Time Measuring Device, Инструкция по эксплуатации

Поделиться
Скачать
Rockford Systems Stop-Time Measuring Device Скачать руководство пользователя страница 27

Rockford Systems, LLC

1-800-922-7533 (U.S.A. only)

27

SECTION 6—FAULT MESSAGES

Stop-Time Measurement Device

Display Message

Cause/Solution

MEMORY FULL

The data for 30 machines is in memory (10 measurements/machine). Print or 
transfer data in 

MM MEASURING DATA MANAGEMENT

 section and delete 

all data after this step is complete.

NO DATA IN MEMORY

There is no data available. Perform measurement tests and data will be stored 
in memory.

ACTUATOR FEED BACK OVERFLOW

The actuator is defective or the delay time is not correct. Carry out an actuator 
test in the M

M TEST FUNCTION AND SERVICE

 section and try another 

measurement test. If this message continues, recharge the battery.

MEASURING DEVICE DOES NOT 
ACCEPT ANY COMMANDS

Press all three function operation buttons simultaneously to reboot

OTHER FAILURES

Reset factory default settings in 

MM TEST FUNCTION AND SERVICE

. 

Delete all measurement data in the 

MM MEASURING DATA MANAGEMENT

 

section.

STORED DATA SHOWS INCORRECT 
FORMATTING

Delete all measurement data in the 

MM MEASURING DATA MANAGEMENT 

section.

PRINTER SHOWS MISTAKES 
PRINTER OR ACTUATOR IS NOT 
WORKING CORRECTLY

Check the cable connection.

LOW BATTERY

Charge the battery.

Table 6.1

SECTION 7—REPLACEMENT PARTS

Part No.

Description

DCL-034

STOP-TIME meter

DCL-043

Sensor

DCL-044

Actuator

DCL-045

Flag

DCL-046

Sensor base magnet

DCL-047

Magnet for ram attachment

Part No.

Description

DCL-048

Allen wrench

DCL-049

Actuator spacer

DCL-050

Actuator pushbutton plate

DCL-051

Printer

DCL-052

Cord and plug for printer

DCL-053

Insturction label

Содержание Stop-Time Measuring Device





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды