Robotis Dynamixel RX-64 Скачать руководство пользователя страница 42

Страница: 42 / 49

RX-64

Locates at the Position 180° with the speed of 57RPM.

Hint

Sets Goal Position (Address 30 (0x1E))= 511 (0x1FF) and

Moving Speed (Address 0x20))= 512 (0x200).

Instruction = WRITE_DATA, Address = 0x1E,

DATA

0x00,

0x02,

0x00,

0x02

Communication

Instruction Packet: FF FF 01 07 03 1E 00 02 00 02 D3

Status Packet : FF FF 01 02 00 FD

Status Packet Result

ERROR

Example 17

Turns on the LED and enables Torque.

Hint

Instruction = WRITE_DATA, Address = 0x18,

DATA

0x01,

0x01

Communication

Instruction Packet: FF FF 01 05 03 18 01 01 DD

Status Packet : FF FF 01 02 00 FD

Status Packet Result

ERROR

You can check the Torque Enable state by touching the axis of Dynamixel you’re

your hand.

Example 16

Sets the Alarm as such that LED flickers and shutdown (torque off)

when the operating temperature is higher than the limit temperature.

Hint

Since Overheating Error is Bit 2, set up Alarm value as

0x04.

(

0x04=00000100

)

Instruction = WRITE_DATA, Address = 0x11,

DATA

0x04,

0x04

Communication

Instruction Packet: FF FF 01 05 03 11 04 04 DE

Status Packet : FF FF 01 02 00 FD

Status Packet Result

ERROR

Example 15

Содержание Dynamixel RX-64


















































Результаты поиска

Содержание Dynamixel RX-64

Отзывы:

Похожие инструкции для Dynamixel RX-64

Бренды по названию

Популярные бренды

Robotis Dynamixel RX-64, Руководство пользователя

Результаты поиска

Содержание Dynamixel RX-64

Отзывы:

Похожие инструкции для Dynamixel RX-64

Бренды по названию

Популярные бренды