ROBBE Valdivia, Руководство по сборке и эксплуатации

Страница: 96 / 165

Assembly instructions
Valdivia
Order No.
1140
Stage 7, the main winch
Part Description Material Dimensions No. Note
No. off
7.1 Main winch 1 N.I.
7.2 Outrigger Plywood, ready made 3 1 Sheet C
7.3 Screw Steel M2.5 x 14 4 FS
7.4 Nut Brass M2.5 4 FS
7.5 Bracket Aluminium 2 x 8 x 20 x 15 2 FS
7.6 Retaining screw Brass M3 x 20 1 FS
7.7 Servo output disc Plastic 1 FS
7.8 Sprocket Plastic 22-tooth 1 FS
7.9 Hexagon driver Brass 8 x 10 x 3 Ø 2 FS
7.10 Nut Brass M3 1 FS
7.11 Self-tapping screw Steel 2.2 x 6.5 3 FS
7.12 Washer Brass 2.6 Ø 3 FS
7.13 Sheet drum Aluminium 20 / 12 Ø x 5 1 FS
7.14 Sprocket Plastic 11-tooth 1 FS
7.15 Guide disc ABS, die-cut 1 x 60 Ø 1 Sheet D, FS
7.16 Spacer disc ABS, die-cut 1.5 x 24 / 9.5 Ø 1 Sheet B
7.17 Screw Brass M2.5 x 20 1 FS
7.18 Self-locking nut Steel M3 1 FS
7.19 Ring-screw Brass M2.5 x 30 1 FS
7.20 Nut Brass M2.5 2 FS
7.21 Triangular section strip ABS section 5 / 5 / 7 x 30 3
7.22 Deflector plate ABS, die-cut 1 x 30 x 270 1 Sheet D, FS
7.23 Timing chain Steel 900 long 1 FS
7.24 Deflector plate ABS, die-cut 1 x 25 x 85 1 Sheet D, FS
7.25 Mounting plate Plywood, ready made 3 1 Sheet C
7.26 Self-tapping screw Steel 2.9 x 9.5 2 FS
- The next step is to assemble the drive unit: fit together the
sheet drum 7.13, the guide disc 7.15, the spacer disc 7.16
and the large sprocket, and fix this assembly to the sail-
winch using the screw 7.17 - Fig. 92.
- Re-install the retaining screw 7.6 and nut 7.10. Fit the
small sprocket and tighten the self-locking nut 7.18 to the
point where it still just rotates freely.
- Solder up the loop of the ring-screw 7.19 to close it, and
install it using the nuts 7.20 as shown in Fig. 93.
- Cut the triangular-section strips 7.21 to length and glue
them to the deflector plate 7.22 as shown in Fig. 94.
- Glue the deflector plate 7.22 in place as shown in Fig. 95.
- Lay the chain 7.23 over the sprockets and place it under
light tension; check that it is engaged over both sprockets.
- Glue the deflector plate 7.24 in place - Fig. 96.
- Glue the mounting 7.25 to the underside of the edge of the
main hatch. Note that the fore-and-aft and transverse
edges must lie flush with the edges of the hatch opening:
see Figs. 97 and 98.
[Fig. 97: vorn = forward]
[Fig. 98: vorn = forward]
- The main winch is later fixed to the mounting plate using
the self-tapping screws 7.26.
9
- Press the rubber grommets and metal eyelets into the
mounting lugs of the sailwinch 7.1.
- Fix the winch to the plywood outrigger 7.2 using two scr-
ews 7.3 and nuts 7.4 - Fig. 85.
- Drill holes in the aluminium brackets 7.5 as shown in Fig.
86 and screw them to the plywood outrigger using the scr-
ews 7.3 and nuts 7.4 - Fig. 87.
- Assemble the sprocket as shown in Fig. 88. Fit the retai-
ning screw 7.6 through the servo output disc 7.7 from the
flanged side, and fit the sprocket 7.8 and hexagon driver
7.9 on it.
- Fit and tighten the nut 7.10 to hold the assembly together.
- Continue the 1.5 mm Ø holes in the servo output disc
through the sprocket.
- Dismantle the assembly and open up the holes in the
servo output disc to 2.5 mm Ø, then mantle the assembly
back together again.
- Screw the servo output disc to the sprocket (7.11), fitting
the washers 7.12 between them - Fig. 89.
- Remove the driver 7.9 and the screw 7.6.
- Fit the sheet drum 7.13 and the small sprocket 7.14 on the
drivers 7.9, and splay the ends to retain them - Fig. 90.
- Drill a 1.2 mm Ø hole in the sheet drum - Fig. 91.