ROBBE Valdivia, Руководство по сборке и эксплуатации

Страница: 106 / 165

Assembly instructions
Valdivia
Order No.
1140
strakes 17.15 and 17.14 on the left-hand side. Place the
core piece 17.17 against the rail as a spacer, and glue the
second rail to the roof. Don’t glue the core in place at this
stage - Fig. 192.
- Note: the next step is to make the sliding hatch, but it is
best to make two of them at the same time; the second
hatch is required for the cabin.
- Glue the front and rear hatch panels 17.18 on the obechi
core piece 17.17. Glue three roof strakes 17.19 on each
side of the centreline, then sand back the roof planking
flush with the core along the long edges.
- Glue the corner strakes 17.20 in place, packing them up on
the jig strip “HL”, and round off the edges as shown when
the glue is hard.
- Bend the handles 17.21 to shape and install them - Fig.
193.
- Sand the roof back between the rails 17.16 as far as the
back panel 17.5 in order to accommodate the loose
bulkhead - Fig. 194.
- Glue the vertical rails 17.22 and the loose bulkhead com-
ponents 17.23 in place - Fig. 195.
- The sliding hatch is secured by fitting the screw 17.24
through the housing roof from the underside.
19
Stage 18, central light shaft
Part Description Material Dimensions No. Note
No. off
18.1 Light shaft housing PVC Vac. 1 Clear
18.2 Side panel Spruce Veneer 2 Sheet F, FS
18.3 Front panel Spruce Veneer 2 Sheet F, FS
18.4 Corner piece Spruce 5 x 5 x 20 4
18.5 Frame strip Spruce 2 x 2 x 90 2
18.6 Frame strip Spruce 2 x 2 x 30 4
18.7 Long roof light frame Spruce 1.2 x 5 x 90 4 FS
18.8 Short roof light frame Spruce 1.2 x 5 x 22 10 FS
18.9 Ridge strake Spruce 2 x 5 x 90 1
- Glue the front and side panels 18.2 and 18.3 to the moul-
ded light shaft housing, then apply the corner pieces 18.4
- Fig. 197.
- Notch the corner pieces to accept the frame strips 18.5
and 18.6, and glue these parts in place. The frame strips
18.6 must be mitred accurately in the ridge area - Fig. 198.
- Glue the long roof light frames 18.7 in place, then add the
short roof light frames 18.8, spaced out equally.
- Sand the ridge flat so that the ridge strake 18.9 can be
glued on without any gaps - Figs. 199 and 200.
Stage 19, aft light shaft
Part Description Material Dimensions No. Note
No. off
19.1 Light shaft housing PVC Vac. 1 Clear
19.2 Dividing strip Spruce 2 x 2 x 65 2
19.3 Front panel Spruce Veneer 2 Sheet F, FS
19.4 Side panel Spruce Veneer 2 Sheet F, FS
19.5 Corner piece Spruce 5 x 5 x 20 4
19.6 Long roof light frame Spruce 1.2 x 5 x 72 4 FS
19.7 Frame strip Spruce 2 x 2 x 28 4
19.8 Short roof light frame Spruce 1.2 x 5 x 15 8 FS
19.9 Ridge strake Spruce 2 x 5 x 72 1
19.10 Stowage box hatch Spruce 3 x 5 x 72 10
- Glue the dividing strips 19.2 to the moulded light shaft hou-
sing 19.1 - Fig. 201.
- Attach the front panels 19.3 and the side panels 19.4 and
sand them to follow the shape of the housing - Fig. 202.
- Attach the corner pieces 19.5.
- Glue in place the long roof light frames 19.6 with an equal
overhang at both ends. Mitre the frame strips 19.7 and glue
them under the strips 19.6 - Fig. 203.
- Install the short roof light frames 19.8, and glue the ridge
strake 19.9 on top.
- The hatch covers are formed by gluing the strips 19.10 to
the structure, starting from the dividing strips - Fig. 204.