Rigol DS4000E Series Скачать руководство пользователя страница 73

Страница: 73 / 278

Chapter 2 Command System

RIGOL

DS4000E Programming Guide

2-61

Remarks



20M|100M: enables the bandwidth limit and sets the bandwidth limit to 20 MHz or 100 MHz. The

high-frequency components that are greater than 20 MHz or 100 MHz in the signal under test will be

attenuated.



OFF: disables the bandwidth limit function. The high-frequency components in the signal under test

can pass through the channel.

Return Format

The query returns 20M, 100M, or OFF.

:CHANnel<n>:COUPling

Syntax

:CHANnel<n>:COUPling <coupling>

:CHANnel<n>:COUPling?

Description

Sets or queries the coupling mode of the specified analog channel.

Parameter

Name

Type

Range

Default

<n>

Discrete

{1|2|3|4}

Discrete

{AC|DC|GND}

Remarks



AC: the DC components of the signal under test are blocked.



DC: both DC and AC components of the signal under test can pass through the channel.



GND: both DC and AC components of the signal under test are blocked.

Return Format

The query returns AC, DC, or GND.

:CHANnel<n>:CSTart

Syntax

:CHANnel<n>:CSTart

Description

Starts calibration for the active probe currently connected to the specified analog channel.

Parameter

Name

Type

Range

Default

<n>

Discrete

{1|2|3|4}

Remarks

This command is only valid when an active probe is correctly connected.

Содержание DS4000E Series























































































































































































































































































Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol DS4000E Series, Руководство по программированию

Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды