Rigol DS4000E Series Скачать руководство пользователя страница 123

Страница: 123 / 278

Chapter 2 Command System

RIGOL

DS4000E Programming Guide

2-111

Parameter

Name

Type

Range

Default

<bool>

Bool

{{1|ON}|{0|OFF}}

0|OFF

Remarks

The display of the statistic information of the pass/fail test results can only be turned on when the pass/fail

test function is enabled (refer to the :MASK:ENABle command).

Return Format

The query returns 1 or 0.

:MASK:OPERate

Syntax

:MASK:OPERate <oper>

:MASK:OPERate?

Description

Runs or stops the pass/fail test operation.

Parameter

Name

Type

Range

Default

<oper>

Discrete

{RUN|STOP}

STOP

Remarks

You can only run the pass/fail test operation when the pass/fail test function is enabled (refer to

the :MASK:ENABle command).

Return Format

The query returns RUN or STOP.

:MASK:OUTPut

Syntax

:MASK:OUTPut <type>

:MASK:OUTPut?

Description

Enables or disables the alarm function; or queries the on/off status of the alarm function.

Parameter

Name

Type

Range

Default

<type>

Discrete

{FAIL|FSOund}

FAIL

Remarks



FAIL: When a failed waveform is detected, the oscilloscope displays the statistic results and outputs a

pulse; but the beeper does not sound.



FSOund: When a failed waveform is detected, the oscilloscope displays the statistic results and outputs

a pulse; while at the same time, the beeper sounds regardless of the on/off status (refer to

the :SYSTem:BEEPer command) of the beeper.

Return Format

The query returns FAIL or FSO.

Содержание DS4000E Series























































































































































































































































































Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol DS4000E Series, Руководство по программированию

Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды