Rigol DS4000E Series Скачать руководство пользователя страница 33

Страница: 33 / 278

Chapter 2 Command System

RIGOL

DS4000E Programming Guide

2-21

Remarks

You can send the :BUS<n>:PARallel:SLOPe command to sample data channel's data on the rising edge,

falling edge, or either of the edges of the clock signal. When <source> is set to "OFF" (disabling the clock

channel), sampling is performed when a hop occurs to the data of the data channel during decoding.

Return Format

The query returns CHAN1, CHAN2, CHAN3, CHAN4, or OFF.

:BUS<n>:PARallel:OFFSet

Syntax

:BUS<n>:PARallel:OFFSet <val>

:BUS<n>:PARallel:OFFSet?

Description

Sets or queries the vertical position of Parallel decoding on the specified bus.

Parameter

Name

Type

Range

Default

<n>

Discrete

{1|2}

<val>

Integer

Refer to Remarks

Remarks



Before using the command, enable the display of the specified decoding bus (refer to

the :BUS<n>:DISPlay command).



The range of <val> is related to the screen display mode and the on/off status of the statistic function

(refer to the :MEASure:STATistic:DISPlay command).

When the display mode is "Full Screen" and the statistics function is disabled, the <val> parameter

ranges from -166 to +148.

When the display mode is "Full Screen" and the statistics function is enabled, the <val> parameter

ranges from -163 to +143.

When the display mode is "Split" (refer to the :TIMebase:DELay:ENABle and :CALCulate:FFT:SPLit

command), the <val> parameter ranges from -103 to +52.



When the data line that displays the decoding is located in the middle part of the screen, <val> is 0;

when it is located above the middle part of the screen, <val> is a positive value; when it is located

below the middle part of the screen, <val> is a negative value.

Return Format

The query returns an integer.

:BUS<n>:PARallel:SLOPe

Syntax

:BUS<n>:PARallel:SLOPe <slope>

:BUS<n>:PARallel:SLOPe?

Description

Sets or queries the edge type of the clock signal of Parallel decoding on the specified bus.

Parameter

Name

Type

Range

Default

<n>

Discrete

{1|2}

<slope>

Discrete

{POSitive|NEGative|BOTH}

POSitive

Содержание DS4000E Series























































































































































































































































































Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды

Rigol DS4000E Series, Руководство по программированию

Результаты поиска

Содержание DS4000E Series

Отзывы:

Бренды по названию

Популярные бренды