Riello Family KIS, Инструкция по установке и эксплуатации

Страница: 23 / 188

ENGLISH
23
For fault E060
The boiler is working normally, but does not provide any stability of the domestic hot water
temperature that, in any event, is supplied at a temperature of around 50°C. The intervention
of the Technical Assistance Service is required.
For fault E091
The boiler has an auto-diagnostic system which, based on the total number of hours in
certain operating conditions, can signal the need to clean the primary exchanger (alarm
code E091).
Once the cleaning operation has been completed, reset to zero the total hour meter with
special kit supplied as an accessory following procedure indicated below :
-
access the technical parameters as explained in the section“ Accessing the technical
parameters”
-
select EXHAUST PROBE RESET with the “ UP ” and “ DOWN ” keys, confirming the
selection
RANGE RATED
CALIBRATION
WEATHER COMPENSATION
COMBUSTION ANALYSIS
EXHAUST PROBE RESET

INSTALLER
TECHNICAL
- select CONFIRM to confirm the reset of the flue gas probe meter or else “ BACK ” to
cancel the operation
CONFIRM OR DELETE SELECTION
CONFIRM CANCEL
THE PARAMETER WILL BE
CHANGED
Note: The meter resetting procedure should be carried out after each in-depth cleaning of
the primary exchanger or if this latter is replaced.
The total hours can be verified in the following way:
- select INFO on the initial screen of the REC10 and press “ ENTER ”
30
°C
.3
MENU STATE
SET
INFO
HOT WATER TEMPERATURE
FRI
1.3
bar
18/05/2013 12:17
PLANT
- using the “ UP ” and “ DOWN ” keys select FLUE GAS PROBE and press “ ENTER ” to
display the value of the flue gas probe meter.
Boiler faults list
ERROR CODE COLOUR DISPLAYED ERROR MESSAGE DESCRIPTION OF TYPE OF ALARM
E010 Yellow flame lockout/ACF electronic fault definitive
E011 Yellow extraneous flame transitional
E020 Red limit thermostat definitive
E030 Red fan fault definitive
E040 Yellow water transducer – load system definitive
E041 Yellow water transducer - press OK to fill the system transitional
E042 Yellow water pressure transducer fault definitive
E060 Yellow Domestic hot water probe fault transitional
E070 Red
flow sensor faulty
flow sensor overtemperature
flow/return sensor differential alarm
transitional
definitive
definitive
E077 Red main zone water thermostat transitional
E080 Yellow
return line probe fault
return line probe overtemperature
outlet/return line probe differential alarm
transitional
definitive
definitive
E090 Red
flue gas probe faulty
flue gas probe overtemperature
transitional
definitive
E091 Yellow clean primary heat exchanger transitional
E099 It is referred to the last fault occurred reset attempts exhausted, boiler blocked definitive, not resettable
-- Yellow water pressure low press OK to charge transitional
-- Red water pressure high check system transitional
-- Red boiler board communication lost transitional
-- Red BUS 485 communication lost transitional
List of combustion faults
ERROR CODE COLOUR DISPLAYED ERROR MESSAGE DESCRIPTION OF TYPE OF ALARM
E021 Red ACC monitor error
These are temporary alarms that if they occur 6 times in an hour they become definitive; the alarm E097 is
displayed and is followed by post-purging for 45 seconds at the fan's maximum speed.
It is not possible to release the alarm before the end of the post-purging unless the boiler's power supply is
switched off.
E022 Red ACC monitor error
E023 Red ACC monitor error
E024 Red ACC monitor error
E067 Red ACC monitor error
E088 Red ACC monitor error
E097 Red ACC monitor error
E085 Red incomplete combustion
These are temporary alarms that if they occur several times in an hour they become definitive; the last error to
occur is displayed and is followed by a post-purging of 5 minutes at the fan's maximum speed.
It is not possible to release the alarm before the end of the post-purging unless the boiler's power supply is
switched off.
E094 Red incomplete combustion
E095 Red incomplete combustion
E058 Red mains voltage fault
These are temporary faults that restrict the ignition cycle.
E065 Red current modulation alarm
E086 Red flue gases obstruction alarm Temporary fault signalled during Pre-Purging. Post-Purging is maintained for 5 min at maximum fan speed.