Riello 20161608, Инструкции по установке и техническому обслуживанию

Страница: 39 / 68

39
INStAllAtION
fault signals description
The following tables include lists of alarm signals, their probable cause, effect on the unit and the type of reset.
Alarm
Inverter
Alarm [P350]
- [P354] or
[P360] -
[P364]
Description Unit status
Reset type
Verifications
Automatic feeding cycle Comment
- 1 EWT sensor failure Continue X
When the operating values return to
the correct range.
1. Check the EWT sensor (EWT).
2. Check NHC card.
- 2 LWT sensor failure Stop X
When the operating values return to
the correct range.
1. Check the LWT sensor (LWT).
2. Check NHC card.
- 3 Coolant temperature sensor (TR) failure Stop cpr X
When the operating values return to
the correct range.
1. Check the TR sensor (TR).
2. Check NHC card.
- 4 OAT sensor failure Continue X
When the operating values return to
the correct range.
1. Check the auxiliary OAT sensor (OAT).
2. Check NHC card.
- 5 DHW_TT sensor failure DHW failure X
When the operating values return to
the correct range.
1. Check the DHW sensor (DHW).
2. Check NHC card.
- 6 CHWSTEMP sensor failure X
When the operating values return to
the correct range.
1. Check the CHWSTEMP sensor
(CHWSTEMP).
2. Check NHC card.
- 7 IAT sensor failure Continue X
When the operating values return to
the correct range.
1. Check the IAT sensor (IAT).
2. Check NHC card.
- 8 Internal IU temperature faults Continue X
When the operating values return to
the correct range.
1. Check the internal temperature
sensor UI.
2. Check NHC card.
- 9 Replacement sensor failure Continue X
When the operating values return to
the correct range.
1. Check the replacement sensor.
2. Check NHC card.
10
Inverter discharge temperature sensor
failure (TD)
Stop cpr X
This error becomes permanent after 4
attempts to complete the operation.
1. Check the discharge temperature
sensor (TD).
102 11
Inverter air exchanger temperature
sensor failure(TE)
Stop cpr X
This error becomes permanent after 4
attempts to complete the operation. 1. Check the temperature sensor (TE).
103 12
Inverter liquid temperature sensor
failure (TL)
Stop cpr X
This error becomes permanent after 4
attempts to complete the operation. 1. Check the temperature sensor (TL).
104 13 TO inverter sensor failure Continue X
The operation of the unit continues
in emergency mode.
1. Check the outdoor temperature
sensor (TO).
The sensor value is set at 30 ° C in
cooling, 10 ° C in heating
the emergency mode is canceled
when any other value is detected by
the TO sensor.
108 14
Inverter suction temperature sensor
failure (TS)
Stop cpr X
This error becomes permanent after 4
attempts to complete the operation.
1. Check the suction temperature
sensor (TS).
109 15 Inverter heatsink temperature failure Stop cpr X
This error becomes permanent
after 8 attempts to complete the
operation.
1. Check the correct functioning of
the fan
111 16
TE and TS inverter sensors incorrectly
connected
Stop cpr X
This error becomes permanent after 4
attempts to complete the operation.
1. Check the temperature sensor
(TE, TS).
- 20
Loss of communication with user
interface
Continue X
When a new message is received
from the user interface
- 21 Communication loss with inverter Stop cpr X
When a new message is received
from the user interface
221 22
Communication error between the
inverter boards
Stop cpr X Simple delay in communication.
- 23 Loss of communication with the slaves Continue X
Only the Master unit continues to
work.
- 24 Loss of communication with the Master Stop X
25 Loss of communication with the Master Stop X
When a new message is received
from the Master
- 31 Security entrance
Stop O Stop
heating OR Stop
cooling
X When the security entrance is closed
- 32 Flow switch failure Stop cpr X
This error becomes permanent after 5
attempts to complete the operation.
- 50
Exchanger antifreeze protection based
on water temperature (in cooling)
Cooling down X
Ignition of antifreeze heaters, if
present, when the alarm is active.
The pump is forced to start.
- 51
Exchanger frost protection based on
the temperature of the refrigerant (in
cooling)
Cooling down X
Ignition of antifreeze heaters, if
present, when the alarm is active.
The pump is forced to start until
the manual reset of the alarm
is possible. The alarm becomes
blocking when it is repeated 12 times
in 2 hours.